To Next PageTo Next Page
Why is my Graco Paint Sprayer sputtering?
If you're experiencing intermittent flow, sputtering, or air in the material of your Graco Paint Sprayer: * Check the gasket and tighten the connection if the hopper connection isn't tight. * Clean the system if there is debris.
What to do if my Graco RTX 1500 Paint Sprayer won't run?
If your Graco Paint Sprayer won’t run, there are several potential causes: * The power switch may not be on. Turn the switch on. * There may be no power at the wall outlet. Check the outlet by plugging in another appliance. If that appliance doesn't work, try a different outlet. * The temperature may be too cold. Allow the unit to warm up. * Too many items might be on the same circuit. Unplug other items from the circuit. * The internal thermal switch may have tripped. Allow the unit to cool down for 15 minutes and restart. This often happens when the wrong size extension cord is used. * The extension cord may be too long or the wrong gauge. Use a 12 gauge extension cord or remove the extension cord. * The breaker might have tripped. Reset the breaker.
Why is material running out of the bottom of my Graco RTX 1500?
If material is running out of the bottom of your Graco Paint Sprayer: * Replace the hose if the RotoFlex HD Pump is worn out. * Check and retighten all fittings if they are loose.
What to do if the needle adjustment won't adjust on my Graco RTX 1500 Paint Sprayer?
If the needle adjustment won't adjust on your Graco Paint Sprayer: * Clean the threads if they are dirty. * Put the nozzle on the gun if it is not on. * Turn the flow nut adjustment the other way if the flow nut is set to maximum adjustment.
Why is there no air coming from my Graco RTX 1500 compressor?
If there's no air coming from your Graco Paint Sprayer compressor, check the following: * Ensure the gun air valve is open. * Clean the needle if it's plugged and retry. * Verify all quick disconnect connections to the gun and hoses are properly connected. * Replace the hose if it's damaged.
How to increase the application speed of my Graco RTX 1500 Paint Sprayer?
If the application speed of your Graco Paint Sprayer is too slow: * Thin the material if it's too thick. * Increase the flow control setting. * Clean the gun if it's plugged or dirty. * Unkink the hose if it's kinked. * Increase flow adjustment with flow adjustment nut if the gun fluid flow adjustment is set too low.
What to do if soft start doesn't work on Graco RTX 1500?
If the soft start isn't working on your Graco Paint Sprayer: * Release the trigger for 10-15 seconds and retry if there is a normal soft start system delay. * Replace the switch if the switch is not operating properly. * Check the gun supply, hose, and sprayer for leaks if there is a damaged solenoid valve on the cylinder.
What to do if my Graco Paint Sprayer gun will not shut off?
If your Graco Paint Sprayer gun will not shut off: * Replace worn parts if the nozzle or needle is worn. * Clean if there is debris in the needle passage.
General| Brand | Graco |
|---|---|
| Model | RTX 1500 |
| Category | Paint Sprayer |
| Language | English |
Lists supplementary manuals for the RTX 1500 Electric Texture Sprayer.
Details hazards related to flammable materials and vapors, and prevention measures.
Outlines risks associated with improper use, modification, or maintenance of the sprayer.
Explains risks of electric shock due to improper grounding, setup, or usage.
Warns about injuries from high-pressure air or fluid, and proper pressure relief procedures.
Advises on compatible solvents to prevent damage to plastic components and potential injury.
Lists essential protective gear required for safe operation and servicing of the equipment.
Describes the standard procedure for priming the RTX 1500 sprayer with material.
Details an alternative priming method when material flow with air is not desired.
Step-by-step guide to safely relieve pressure from the sprayer system before maintenance.
Explains the importance of proper grounding for electrical safety and how to achieve it.
Provides guidelines for selecting and using extension cords with the sprayer for safe operation.
Details when and how to use an auxiliary air compressor with the RTX 1500 sprayer.
Specifies the minimum generator power required to operate the RTX 1500 sprayer.
Offers recommendations on hose length for optimal performance and potential issues.
Instructions for safely detaching and reattaching the sprayer's hopper.
Describes the process of wetting the hose before use to prevent material buildup.
Provides a chart for selecting the appropriate nozzle based on application and desired finish.
Explains how to adjust the material flow rate using the fluid flow regulator knob.
Details how to regulate the air flow using the air valve on the gun handle.
Tips to avoid material surges when triggering the gun for smoother application.
Advice on using the trigger lock for extended spraying sessions and reduced fatigue.
