Graco RTX5500 - User Manual

Other manuals for Graco RTX5500

Installation12 pages

Questions and Answers

A
Ashley OconnorAug 15, 2025
What to do if my Graco RTX5500 won't run?
- H
  Haley MillerAug 15, 2025
  If your Graco Paint Sprayer isn't running, there are several potential causes: * The power switch may not be turned on. Ensure the switch is in the ON position. * The wall outlet may not be providing power. Test the outlet by plugging in another appliance. If it doesn't work, try a different outlet. * The generator may not be powerful enough. Use a 7500 watt or larger generator. * The circuit breaker may have tripped. Try resetting the breaker.
W
Willie Carrillo Jr.Aug 18, 2025
Why is fluid leaking at the flow adjustment nut of my Graco Paint Sprayer?
- G
  grant40Aug 18, 2025
  If fluid is leaking at the Flow Adjustment Nut, it is likely due to a damaged seal.
K
Karen EllisAug 21, 2025
Why is my Graco RTX5500 pump not pumping material?
- D
  David MartinezAug 21, 2025
  Several factors can prevent your Graco Paint Sprayer pump from pumping material: * An air lock may be present. Open the air control valve on the gun. * The mix might be too thick. Thin the material by adding water, using a Material Thickness Gauge. * Fittings could be loose. Check and retighten all fittings. * The gun might be plugged. * The pump hose may be worn out. Replace the hose, ideally once a year. * The pump could be cold. Move it to a warm room or run hot water through the sprayer.
C
Christine HayesAug 25, 2025
What to do if my Graco RTX5500 motor won't run, even when plugged in?
- C
  Carrie DeanAug 25, 2025
  If your Graco Paint Sprayer motor doesn't run and the pump doesn't cycle, even when plugged in and the power switch is on, consider these possibilities: * The air control valve on the gun may be closed or not open enough. Open the air control valve. * The motor or control may be damaged. Take the sprayer to a Graco authorized service center. * The electric outlet may not be providing power. Try a different outlet or plug in something that you know is working to test the outlet. Reset the building circuit breaker or replace the fuse. * The extension cord may be damaged. Replace the extension cord. * The sprayer electric cord may be damaged. Check for broken insulation or wires. Replace the electric cord if damaged.
M
Melissa MaldonadoAug 27, 2025
Why won't my Graco RTX5500 Paint Sprayer gun shut off?
- W
  William RobinsonAug 27, 2025
  If your Graco Paint Sprayer gun won't shut off, it could be due to: * A worn nozzle or needle. * Debris in the needle passage.
S
Stacy VaughnAug 30, 2025
What could cause my Graco Paint Sprayer motor to not run, even when the power switch is on?
- L
  liularryAug 30, 2025
  If your Graco Paint Sprayer motor isn't running even with the power switch on, consider these issues: * Material and/or water may be frozen or hardened in the pump. Unplug the sprayer. If frozen, do NOT try to start it until it is completely thawed, or you may damage components. Place the sprayer in a warm area for several hours. Then plug it in and turn it ON. Slowly increase the pressure setting to see if the motor will start. If the material is hardened, the pump or pressure switch may need replacement. Take the sprayer to a Graco authorized service center. * The prime valve may be plugged. Remove and clean the prime valve. * The gun may be plugged. Disassemble and clean the gun.
K
Kristin EstradaSep 2, 2025
Why doesn't my Graco RTX5500 start when the gun is triggered?
- R
  Robert MaddenSep 2, 2025
  If your Graco Paint Sprayer doesn't start when the gun is triggered, it may be because the flow switch is stuck. Replace the flow switch.
M
Michelle RichardsonSep 5, 2025
How to fix slow application speed on a Graco RTX5500 Paint Sprayer?
- S
  Samuel SmithSep 5, 2025
  If your Graco Paint Sprayer's application speed is slow, consider these solutions: * The material may be too thick. Thin the material. * The nozzle may be too small. * Too much air might be in use. Partially close the gun air control valve to reduce airflow. * The pump hose could be worn. Replace the hose. * The gun may be plugged or dirty. * The hose may be kinked. Unkink the hose. * The gun adjustment might be set too low. Increase the flow adjustment with the flow adjustment nut. * Too many items might be on the same circuit. Unplug other items from the circuit. * The extension cord may be too long or the wrong gauge.
G
gerald85Sep 8, 2025
Why does my Graco RTX5500 continue to run after releasing the gun trigger?
- M
  meghan26Sep 8, 2025
  If your Graco Paint Sprayer continues to run after you release the gun trigger, here are some possible causes: * The pressure switch may be damaged. Replace the pressure switch. * There may be a compressed air system leak. Locate the leak, checking the gun, twin line hose, or internal system. Reseal the leaky fitting or replace the hose. * The flow switch may be stuck. Replace the flow switch.
M
Mrs. Brittany Evans MDSep 12, 2025
Why does my Graco RTX5500 cycle on and off when the trigger is released?
- J
  jordan60Sep 12, 2025
  If your Graco Paint Sprayer cycles ON and OFF when the trigger is released, or when the gun is triggered, the following reasons are possible: * The pressure switch may be damaged. Replace the pressure switch. * There may be a compressed air system leak. Locate the leak; check the gun, twin line hose, or internal system. Reseal the leaky fitting or replace the hose. * The flow switch may be stuck. Replace the flow switch. * The check valve may be damaged. Replace the check valve.