GRANULDISK Granule Maxi

Other manuals for GRANULDISK Granule Maxi

Service Manual97 pages

Questions and Answers

C
changdianaSep 4, 2025
What to do if the temperature is not reached in rinse tank in my GRANULDISK Granule Maxi?
- G
  grantwilliamSep 4, 2025
  If the temperature is not reached in the rinse tank of your GRANULDISK Washer, reset the alarm by pressing the STOP button. If the alarm continues to appear, contact a service engineer.
A
angelacurtisAug 25, 2025
What to do if the door switch alarm goes off on my GRANULDISK Granule Maxi?
- C
  Charles Wilkerson Jr.Aug 25, 2025
  If the door switch alarm activates on your GRANULDISK Washer, it indicates that the door was opened during operation. Close the door and press the STOP button to reset the alarm.
P
Patricia WaltonAug 25, 2025
What to do if the overheating protector for the wash tank tripped on my GRANULDISK Washer?
- J
  Jonathon SanchezAug 26, 2025
  If the overheating protector trips for the wash tank on your GRANULDISK Washer, it means the wash tank heater has overheated. Clean the level sensor in the wash tank and then reset the overheat protection. If the error happens again within a few hours, contact a service engineer.
S
Stephanie WagnerSep 12, 2025
What to do if water level is too low in wash tank of GRANULDISK Washer?
- G
  gilbertdanaSep 12, 2025
  If the water level is too low in the wash tank of your GRANULDISK Washer, it means the level in the wash tank has fallen erroneously. Contact a service engineer!
A
abauerSep 22, 2025
What to do if there is a system error and control card non operational in GRANULDISK Washer?
- S
  Stephen BrownSep 22, 2025
  If you are experiencing a system error indicating the control card is non-operational on your GRANULDISK Washer, it suggests a component on the control card is broken. Contact a service engineer.
J
Jacob FlemingSep 8, 2025
What should I do if the motor circuit breaker for rinse pump tripped out on my GRANULDISK Granule Maxi Washer?
- J
  Jeff PenaSep 8, 2025
  If the motor circuit breaker for the rinse pump has tripped on your GRANULDISK Washer, it means the motor is overloaded. Contact a service engineer!
M
Monique RichardsSep 1, 2025
Why is the rinse time so short on my GRANULDISK Washer?
- J
  John RhodesSep 1, 2025
  If you're experiencing a short rinse time on your GRANULDISK Washer, it means the rinse water was pumped out too fast, leading to insufficient heating and rinsing. Contact a service engineer!
N
Nicole TaylorSep 23, 2025
How to clean level sensor in GRANULDISK Granule Maxi Washer?
- S
  sanchezcarrieSep 23, 2025
  If you see a 'Clean level sensor' message on your GRANULDISK Washer, the level sensor in the wash tank might be dirty. Also, if the machine has been off for over 4 hours, water might not have fully drained from the wash tank at startup. Empty the wash tank and clean the level sensor in the wash tank.
C
Cassandra DavisSep 16, 2025
What to do if the temperature is not reached in wash tank in GRANULDISK Granule Maxi?
- K
  Kristen JohnsonSep 16, 2025
  If the temperature is not reached in the wash tank of your GRANULDISK Washer, it means the wash water isn't reaching its set temperature during the wash cycle. Clean the level sensor and reset the overheat protection. If the error code reappears within a few hours, contact a service engineer.
M
Miranda RamirezAug 28, 2025
How do I clean the level sensor on my GRANULDISK Washer?
- K
  Karen WalkerAug 28, 2025
  If you suspect the level sensor in your GRANULDISK Washer needs cleaning, it's likely dirty or the water hasn't been exchanged after a long shutdown. Lower the water level and clean the level sensor in the wash tank. Then, refill the tank. If the sensor is already clean, reset the error and set the machine in heating mode to continue heating.