What to do if the motor protector for the right potwash pump tripped on my GRANULDISK Granule Maxi?
If the motor protector for the right potwash pump has tripped on your GRANULDISK Washer, it indicates that the motor is overloaded. Contact a service engineer!
What to do if the temperature is not reached in rinse tank in my GRANULDISK Granule Maxi?
If the temperature is not reached in the rinse tank of your GRANULDISK Washer, reset the alarm by pressing the STOP button. If the alarm continues to appear, contact a service engineer.
How do I clean the level sensor on my GRANULDISK Washer?
If you suspect the level sensor in your GRANULDISK Washer needs cleaning, it's likely dirty or the water hasn't been exchanged after a long shutdown. Lower the water level and clean the level sensor in the wash tank. Then, refill the tank. If the sensor is already clean, reset the error and set the machine in heating mode to continue heating.
How to clean level sensor in GRANULDISK Granule Maxi Washer?
If you see a 'Clean level sensor' message on your GRANULDISK Washer, the level sensor in the wash tank might be dirty. Also, if the machine has been off for over 4 hours, water might not have fully drained from the wash tank at startup. Empty the wash tank and clean the level sensor in the wash tank.
Why does my GRANULDISK Granule Maxi take so long to fill the rinse tank?
If your GRANULDISK Washer displays a 'Long rinse tank filling time' error, it means that the level sensor in the rinse tank hasn't activated within 5 minutes of the solenoid valve opening. Check the water supply to the machine and the solenoid valve for the rinse tank filling. Reset the alarm by pressing the STOP button.
What should I do if the motor circuit breaker for rinse pump tripped out on my GRANULDISK Granule Maxi Washer?
If the motor circuit breaker for the rinse pump has tripped on your GRANULDISK Washer, it means the motor is overloaded. Contact a service engineer!
What to do if water level is too low in wash tank of GRANULDISK Washer?
If the water level is too low in the wash tank of your GRANULDISK Washer, it means the level in the wash tank has fallen erroneously. Contact a service engineer!
What to do if there is a system error and control card non operational in GRANULDISK Washer?
If you are experiencing a system error indicating the control card is non-operational on your GRANULDISK Washer, it suggests a component on the control card is broken. Contact a service engineer.
What to do if the overheating protector for the rinse tank tripped on my GRANULDISK Washer?
If the overheating protector trips for the rinse tank on your GRANULDISK Washer, it means that the rinse tank heater has overheated. You should clean the level sensor and reset the overheat protection. If the error code returns within a few hours, contact a service engineer.
What to do if the overheating protector for the wash tank tripped on my GRANULDISK Washer?
If the overheating protector trips for the wash tank on your GRANULDISK Washer, it means the wash tank heater has overheated. Clean the level sensor in the wash tank and then reset the overheat protection. If the error happens again within a few hours, contact a service engineer.
Introduction to the Granule Maxi® pot washing machine and manual.
Important safety notes, warnings, and precautions for operating the machine.
Specifications, dimensions, capacities, and electrical requirements of the machine.
Information about the special granules used in the machine and their handling.
How to use the QR code for quick access to machine information and guides.
Step-by-step guide to prepare and start the Granule Maxi® machine.
Instructions on how to properly load utensils and cassettes into the machine.
Explanation of the buttons and functions on the machine's control panel.
Detailed steps for selecting programs and running a wash cycle.
How to change the display language of the machine.
Instructions for setting the machine's date and time.
Procedure for collecting and cleaning the granules used in the machine.
Steps for cleaning the internal components of the washing machine.
Procedures for leaving the machine idle overnight or for extended periods.
Explanation of the GD Memo function for maintenance reminders.
Overview of the GDTtool for documentation and hygiene control points.
How to access and interpret operating data directly from the control panel.
Details on tracking electricity and water consumption for operational analysis.
Instructions for downloading operating data using a USB stick.
Information about the optional EcoExchanger unit and its settings.
Explains user-related error codes, their causes, and remedies.
Detailed list of error codes, their meanings, causes, and solutions.
General| Brand | GRANULDISK |
|---|---|
| Model | Granule Maxi |
| Category | Washer |
| Language | English |
To Next Page
