Need help?Do you have a question about the GRAPHTEC FC5100-75 and is the answer not in the manual?
Precautions for safely handling sharp cutting blades.
Instructions for handling cutters and blade length.
Step-by-step guide to attach a cutter pen.
Precautions to take after turning on the plotter.
Location and meaning of the machine's caution label.
Guidelines for the plotter's working environment.
Important considerations for using the plotter.
Procedures for daily maintenance of the plotter.
Recommendations for storing the plotter when not in use.
Verifying all standard accessories are present after unpacking.
Identification of plotter parts and their functions.
Step-by-step guide to install the Accuload system.
Instructions for connecting the plotter to a computer.
Steps for connecting the plotter to a power source.
Details on different cutter blades and their uses.
Identification of cutter pen components.
Procedures for replacing cutter blades.
Explanation of cutter offset value settings.
Instructions for replacing supersteel blades.
Instructions for replacing ceramic and sapphire blades.
Adjusting and setting blade length for optimal cutting.
Overview of the control panel, buttons, and indicators.
How to navigate and select functions from the menu.
Description of the initial menu displayed after power-on.
Steps to change the plotter's display language.
Procedure for turning on the plotter.
Step-by-step instructions for loading media.
Specific instructions for loading sheet media.
Specific instructions for loading roll media.
How to select the type of media loaded in the plotter.
The plotter's initialization process after loading media.
How to set cutting conditions for optimal results.
Quick access functions available on the control panel.
Overview of menu navigation and controls.
How to set the cutting origin point on the media.
Setting origin with the rotate function.
How to copy data from the plotter's buffer.
Function to raise or lower the pen.
Clearing the plotter's receiving buffer.
Advancing the media for cutting.
How to set the cutting origin in HP-GL mode.
Defining the effective cutting area of the plotter.
Adjusting the cutting area width.
Setting page length for roll media.
Rotating the plotter's coordinate axes.
Cutting a reversed image of the data.
Adjusting the size of an image for cutting.
Optimizing cutting time by sorting data.
Setting parameters for axis alignment.
Choosing the tool for axis alignment.
Choosing alignment method (2-point/3-point).
Performing the axis alignment adjustment.
Automatically advancing media to prevent slipping.
Blade control for thick and thin materials.
Choosing between Mode 1 and Mode 2 for emulation.
Enabling/disabling emulation per condition.
Background settings specific to GP-GL commands.
Selecting the display language for the plotter.
Enabling/disabling recognition of GP-GL commands.
Pen control for arc plotting commands.
Setting priority between programmed and manual conditions.
Enabling or disabling pen selection.
Setting initial blade control position.
Setting the unit for displayed coordinates.
Controlling pen movement when pen is up.
Enabling or disabling the media length sensor.
Enabling or disabling the pinch roller position sensor.
Checking if a pen is installed.
Background settings specific to HP-GL commands.
Selecting the display language for the plotter.
Setting plotter response to emulation commands.
Setting priority for cutting conditions.
Enabling or disabling pen selection.
Setting initial blade control position.
Setting coordinate display units.
Controlling pen movement when pen is up.
Enabling or disabling the media length sensor.
Enabling or disabling the pinch roller position sensor.
Adjusting circle and arc resolution for smoother output.
Checking if a pen is installed.
Printing a list of current cutting condition settings.
Outputting plotter codes for communication analysis.
Performing a self-test to check plotter functions.
Issues when plotter power is on or off.
Issues when plotter is on but unresponsive.
Problems with the display or menu.
Specific ROM/RAM error messages.
Issues occurring during plotter initialization.
General problems with plotter operation.
Problems related to the quality of cuts.
Details on error messages and their solutions.
Instructions for connecting via parallel interface.
Instructions for connecting via USB interface.
Instructions for connecting via serial interface.
Pre-configured interface settings.
How to access interface menu before loading media.
Setting programmable resolution for GP-GL.
Configuring RS-232C serial interface settings.
Selecting between GP-GL and HP-GL command modes.
Information on the parallel interface.
Pin assignments for the parallel connector.
Overview of the RS-232C serial interface.
Pin assignments for the serial connector.
Detailed specifications for the FC5100-75 model.
Detailed specifications for the FC5100-100 model.
Detailed specifications for the FC5100-130 model.
List of available optional accessories.
Physical dimensions of the plotter.
Manual for the pounce tool option.
Steps to attach the pounce tool.
Selecting pounce tool via the menu.
Setting conditions for pounce tool operation.
Manual for the plotter stand option.
Instructions for assembling the plotter stand.
Manual for the plotter basket option.
Instructions for assembling the plotter basket.
Manual for the media roll holder option.
Instructions for assembling the media roll holder.
Information on the auto registration mark sensor option.
Description of registration mark patterns.
Specifies the required location for registration marks.
Defines the area for mark detection.
Setting origin relative to registration marks.
Lists media types causing detection issues.
Troubleshooting unrecognized registration marks.
Setting the mode for registration mark sensing.
Choosing alignment method (2-point/3-point).
Selecting AUTO or MANUAL scanning methods.
Procedures for selecting alignment methods.
Detailed steps for the 2-point alignment method.
Detailed steps for the 3-point alignment method.
Shortcut for setting up auto registration marks.
Adjusting the area for mark reading.
Choosing the registration mark pattern type.
Setting the size of the registration mark.
Adjusting distance for registration marks.
Adjusting the axis origin offset.
Function to add weight for media stability.
Adjusting sensor offset for precision.
FCC and regulatory compliance information.
Declaration of product conformity with EU standards.
To Next Page
General