GRAUPNER mc-18

1

GRAUPNER mc-18 Specifications

General

Brand	GRAUPNER
Model	mc-18
Category	Remote Control
Language	English

Summary

Selection of Model Type

Fixed-Wing Aircraft Programming

Hook-up of External Operating Elements

Connecting external switches and controls to the transmitter board.

Allocation of Receiver Outputs

Mapping transmitter functions to specific receiver output channels.

Programming and Code Lists

Basic Transmitter Settings

Code 56: Model Selection

Procedure for selecting or deleting stored model memories.

Code 95: Modulation

Setting the transmitter to PPM or PCM modulation mode.

Code 57: Control Allocation

Assigning control functions to sticks in four different modes.

Model and Trim Adjustments

Code 58: Model Type Selection

Choosing the appropriate model type for programming.

Switch Function Allocation

Code 23: External Switch Allocation

Assigning functions to external switches and reversing their polarity.

Mixer and Servo Configuration

Code 37: Signal Generator Allocation

Free allocation of operating elements to function outlets.

Code 43: V-Tail Mixer

Enabling and configuring the V-Tail mixer function.

Code 11: Servo Reverse

Reversing the direction of servo rotation.

Servo Travel and Limiting Adjustments

Code 15: Neutral Adjust

Adjusting the servo neutral position beyond standard limits.

Code 12: Servo Travel Adjust

Adjusting servo travel range for each direction independently.

Code 19: Servo Travel Restrict

Limiting servo travel range to prevent mechanical issues.

Control Travel and Timer Settings

Code 79: Servo Slow Down

Adjusting servo transit time for smoother movement.

Code 16: Signal Generator Setting

Adjusting control travel for specific signal generators.

Dual Rate and Exponential Settings

Code 34: DREX Switch Allocation

Allocating switches for dual rate and exponential functions.

Code 13: DUAL RATE

Adjustable servo throw reduction for dual rate.

Code 14: EXPONENTIAL

Trim and Data Storage

Code 35: Trim Reduction

Code 59: Trim Data Memory

Model Copying Functions

Code 94: Model Copying

Copying model data between transmitters or to a PC.

Aileron Differential

Code 22: Aileron Differential

Adjusting aileron differential to correct adverse yaw.

Throttle and Manoeuvre Control

Code 17: Throttle Reduction

Code 66: Automatic Program

Channel 1 Switch Functionality

Code 63: Channel 1 Switch

Free Program Mixers

Codes 51, 33, 61 and 71: Free Program Mixer

Programming and adjusting freely programmable mixers.

Channel Mix-Only and Stopwatch Functions

Code 72: MIX-only Channel

Code 97: Stopwatch

Timer and Failsafe Operations

Code 77: FAIL SAFE

Programming failsafe behavior in case of signal loss.

Battery and Transmitter Security

Code 78: FAIL SAFE BAT

Code 88: Input Lock

Code 99: Transmitter Lock

Servo Testing and Position Display

Code 76: Servo Test

Code 74: Servo Position

Switch Position Display and F3 B Programs

Code 73: Switch Position

F3 B Programs (Model Types 6 and 7)

Overview of universal programs for F3B competition models.

F3 B Program Functions

Additional F3 B Program Functions

F3 B Model Switch Function

Code 23: External Switch Allocation for F3 B

Flight Task Pre-sets and Servo Timing

Code 52: TAKE-OFF, SPD, DIST

Code 53: Flap Trim Arrangement

Code 92: Switch Slow-Down

Aileron and Flap Mixer Functions

Code 41: Aileron Rudder Mixer

Code 42: Aileron Flap Mixer

Code 49: Flap Aileron Mixer

PROFITRIM-Module

PROFITRIM Activation and Mixer Adjustments

Code 91: Activating PROFITRIM

Code 48: Flap Elevator Mixer

Code 47: Elevator Flap Mixer

Butterfly Function and Differential Reduction

Codes 44, 45, 46: Butterfly Function

Code 54: Adjusting the Reduction of Differential

Programming Examples for Fixed-Wing Models

2. Executing RESET (Important)

Clearing all model memories to start fresh.

Model Memory and Naming in Programming Examples

Stick Allocation and Model Type in Programming Examples

Idle Trim Adjustment in Programming Examples

Copying Adjustments and Modulation Mode in Programming Examples

Servo Rotation Direction in Programming Examples

Servo Throw Adjustments in Programming Examples

Throw Reduction and Throttle Characteristics in Programming Examples

Trim Storage in Programming Examples

Copying Example - Single Model Memory

Copying Example - All Model Memory

Copying Example - Model Memory to Model Memory (Same Transmitter)