6
ALWAYS keep protective structures, guards, and panels
in good repair, in place and securely fastened. NEVER
modify or remove safety devices.
Keep unit free of grass, leaves, or other debris. Clean up
oil or fuel spills.
Check bags and bagger parts prior to each use for any
holes, abrasions, mildew, or structural damage. Replace
parts when necessary.
Keep all hardware properly tightened.
Maintain or replace safety and instruction labels, as
necessary.
Keep unit free of debris. Clean up oil or fuel spills.
DO NOT store bags with grass in them.
DO NOT use double blade kits while bagging.
For extended storage, clean unit thoroughly. See Engine
Manual for proper storage.
ALWAYS lower cutting mower deck when unit is parked
or stored.
Use only attachments or accessories designed for your
unit and properly installed.
Check attachment components frequently. If worn or
damaged, replace with manufacturer’s recommended
parts.
Grass catcher components are subject to wear, damage
and deterioration, which could expose moving parts or
allow objects to be thrown. Frequently check components
and replace with manufacturer’s recommended parts,
when necessary.
TOOLS REQUIRED
• Wrenches: 7/16", 1/2", 9/16"
•Drill
• 13/32" Drill bit
• Utility Knife
UNPACKING UNIT
IMPORTANT: Remove contents from carton carefully.
Place cover assembly on a flat piece of cardboard to
avoid scratching it.
Package Contents:
Check the contents of your kit for the parts listed in
figure 2:
ASSEMBLY
WARNING: AVOID INJURY. Read and
understand the entire Safety section before
proceeding.
Item Description Qty Part Number
1 Cover Assembly 1 NA
2 Inlet Assembly 1 59207602
3 Hose 1 00697300
4 Counterweight 4 01542200
5 Bag Assembly 3 59207600
6 Upper Mount 1 00460951
7 Lower Mount 1 00455851
8 V-belt - 72-Inch Mower Deck 1 07239700
V-belt - 52-Inch Mower Deck
V-belt - 60-Inch Mower Deck
V-belt - 66-Inch Mower Deck
1
1
1
07236200
07213200
07235800
9 Blower Assembly 1 59207603
10 Exhaust Deflector 1 00610551
11 5/16" Wing Knob 2 07531700
12 3/8" Wing Knob 2 07019300
13 Weight Plate Assembly 1 00451851
14 .31-18 Nyloc Nut 4 06545400
15 .25-20 x .50 Hex Bolt 6 05947900
16 .38-16 x 1.00 Hex Bolt 8 05948700
17 .38-16 Nyloc Nut 16 06545500
18 .38-16 x 1.75 Round Head
Bolt
2 06223800
19 .38-16 x 3.25 Hex Bolt 6 05961100
20 .31-18 x 1.00 Hex Bolt 4 05946900
21 .368/.373 x 3.25 Clevis Pin 2 02747500
22 .406 x 1.50 x .245 Flat
Washer
4 06400006
23 .25-20 Locking Nut 6 06543500
24 Bolt .312-18 x 4.5 2 06228300
25 .375 x .115 Lock Washer 2 06306500
26 5/16" Wing Knob 3 07500008
27 Rubber Bumper 2 07533600
28 52" Blower Baffle - Front 1 00469551
29 60" Blower Baffle - Front 1 00469651
30 .38-16 x .50 Tapping Screw 4 07412900
31 3/8" Spinlock Flange Nut 2 06534900
32 Hair Pin 2 06701000
33 Finger Guard -
52-Inch
1 00483851
34 60-, 66- & 72-Inch Finger
Guard
1 00491851
35 .312 x .734 x .065 Flat
Washer
4 06435800
36 52"/60"/66" Blower Baffle -
Rear
1 00887651
37 72" Blower Baffle - Rear 1 00945151
NOTE: A front blower baffle is not required for 66- or
72-inch Mower Decks.
Item Description Qty Part Number
To Next Page
Loading...
Need help?
General
