To Next Page
L
Lisa FoleyAug 18, 2025
What to do if coulters and openers plugging in no-till conditions with GREAT PLAINS Farm Equipment?
- SseanallenAug 19, 2025
To address coulters and openers plugging in no-till conditions, drill at a slight angle to rows.
What to do if coulters and openers plugging in no-till conditions with GREAT PLAINS Farm Equipment?
To address coulters and openers plugging in no-till conditions, drill at a slight angle to rows.
Why is there uneven seed spacing or uneven stand with GREAT PLAINS Farm Equipment?
Uneven seed spacing or stand can occur due to several reasons. You might be operating at excessive field speed, so reduce your speed. Another cause could be plugging in the feed cups or seed tubes, in which case, clean them out. Alternatively, use a faster drive type speed and close feed cup flutes to a more narrow position.
What to do if opener disks are not turning freely on GREAT PLAINS Farm Equipment?
If the opener disks are not turning freely, several factors could be responsible. Trash or mud might have built up on the disk scraper. Failed disk bearings or a bent/twisted opener frame can also cause this issue, so replace the disk bearings or the opener frame. Also, planting conditions may be too wet, so wait until drier weather.
Why is there uneven seed depth with GREAT PLAINS 706NT Farm Equipment?
Uneven seed depth can be attributed to a few reasons. Operating at excessive field speed can cause this, so reduce your speed. Planting conditions that are too wet can also be a factor, so wait for drier weather.
What to do if press wheels are not compacting soil as desired with GREAT PLAINS 706NT Farm Equipment?
If the press wheels aren't compacting the soil as expected, it could be due to conditions being too wet or cloddy, so wait until drier weather or rework the ground.
Why is the actual seeding rate different than desired with GREAT PLAINS Farm Equipment?
The actual seeding rate might differ from what you want because of a buildup of seed treatment in the feed cup, so clean the seed treatment from the feed cups.
What to do if press wheel or openers plugging with GREAT PLAINS 706NT Farm Equipment?
If the press wheel or openers are plugging, it may be due to planting conditions being too wet, so wait until drier weather. Another cause may be failed disk bearings, so replace them. Also, if you backed up with the drill in the ground, clean it out and check for damage.
Why is there excessive seed cracking with GREAT PLAINS 706NT?
Excessive seed cracking can occur if you're operating at excessive field speed, so reduce your speed. Also, check if the feed cup flutes are not open enough, and if so, open feed cups to a wider position. Another cause may be that the feed cup door handle is not open enough, so open the feed cup door handle to a lower position.
Why does the acremeter not measure accurately with GREAT PLAINS 706NT Farm Equipment?
If the acremeter isn't measuring accurately, it could be due to excessive overlap or gaps between passes, so avoid these. Loose soil and slippage will cause variations in acres registered. Also verify field size.
What to do if feed cup sprockets locked up or twisted feed cup drive shaft with GREAT PLAINS 706NT Farm Equipment?
If the feed cup sprockets are locked up or the feed cup drive shaft is twisted, foreign matter may be lodged in one or more feed cup sprockets, so clean them out and use clean seed. Also, dried liquid insecticide inside feed cups can cause this, so remove the buildup by disassembling each feed cup and scraping the foreign substance from turn surfaces.
Indicates potential personal safety hazard requiring extra precaution.
Signal words (DANGER, WARNING, CAUTION) designate hazard levels.
Be prepared for emergencies by keeping a first aid kit and emergency numbers.
Read and understand safety decals, keep them clean, and replace damaged ones.
Details the 706/1006NT grain drill's design and purpose.
Specifies the drill's primary use for no-till drilling.
Lists the Land Pride compact drill models this manual applies to.
Lists related manuals for the drill, including parts and seed rate.
Explains how to use the manual for safety, assembly, operation, and maintenance.
Lists essential checks before operating the drill.
Provides instructions for safely connecting the tractor to the drill.
Details procedures for operating the drill in the field.
Covers adjustments for coulter depth and down pressure.
Explains how to set the master-slave lift cylinders for coulter depth.
Details adjusting spring pressure for opener disks.
Explains how to set seeding depth using press wheels.
Instructions on adjusting disc spacing for proper contact.
Describes how to set the harrow tine angle for no-till conditions.
Addresses issues with seed spacing and stand uniformity.
Troubleshooting uneven seed depth problems.
Solutions for opener disks that are not turning freely.
Diagnosing and correcting seeding rate discrepancies.
Causes and solutions for excessive seed cracking.
Troubleshooting acremeter inaccuracies.
Lubrication and maintenance for clutch zerks and teeth.
Lubrication schedule for grease banks.
Maintenance for drive chains, including lubrication.
Details the function and ordering of the seed box agitator.
Describes the coil-tine harrow for no-till surfaces.
Provides torque values for various bolt sizes and grades.
Details tire size, inflation, torque, and warranty information.
Diagrams and tooth counts for seed box sprocket configurations.
Diagrams and tooth counts for seed box agitator sprockets.
General| Brand | GREAT PLAINS |
|---|---|
| Model | 706NT |
| Category | Farm Equipment |
| Language | English |
