What to do if Gree GMV-280WM/H-X Inverter has abnormal cooling or heating?
If your Gree Inverter is showing abnormal cooling or heating, close any open doors or windows and draw any curtains or louvers to block direct sunlight. Reduce the number of heat sources in the room. Also, clean the filter if it is blocked with dirt.
Why is my Gree Inverter cooling or heating abnormally?
If your Gree Inverter is not cooling or heating properly, check that the air intake and outlet of both the indoor and outdoor units are free from obstructions. Also, make sure the temperature setting, fan speed, and wind direction are properly adjusted using the wireless remote controller or wired controller.
How to troubleshoot a Gree GMV-280WM/H-X that doesn't run?
If your Gree Inverter isn't running, first ensure it's properly connected to a power supply. Then, verify that the voltage is within the specified range. Check the fuse and breaker, replacing the fuse or reconnecting the breaker if necessary. Also, replace the batteries in the remote controller. Finally, make sure you are within the 8m control range of the remote.
What to do if Gree GMV-280WM/H-X Inverter runs but stops immediately?
If your Gree Inverter runs but stops immediately, the air intake or outlet of either the indoor or outdoor unit might be blocked. Remove any obstructions to resolve this issue.
General| Cooling Capacity | 28.0 kW |
|---|---|
| Heating Capacity | 31.5 kW |
| Refrigerant | R410A |
| Coefficient of Performance (Heating) | 3.6 |
| Power Supply | 380-415V/3Ph/50Hz |
Provides essential safety instructions and guidelines for the proper operation of the air conditioning unit.
Outlines conditions and reasons for which the manufacturer bears no responsibility for injury or loss.
Covers critical warnings and notices regarding unit operation, installation, and handling to prevent hazards.
Details safety measures for installation, electrical work, wiring, and operational precautions.
Describes the inverter technology, capacity range, and product lineups available.
Identifies and illustrates the key components of the outdoor air conditioning unit.
Explains the operating principle of the VRF system in cooling and heating modes.
Provides safety guidelines for installation, repair, moving, and wiring requirements.
Details dimensions, layout, pipe specifications, and site selection for outdoor units.
Specifies necessary clearances for ventilation, maintenance, and installation configurations.
Covers requirements for concrete foundations and shock absorption for unit stability.
Outlines principles for pipeline design, including length, bends, and refrigerant pipe specifications.
Specifies limits for pipe lengths and height differences between units and manifolds.
Details procedures for installing refrigerant piping, manifolds, and applying insulation.
Covers selection of insulation materials and methods for wrapping refrigerant pipes.
Provides steps and preparation requirements for installing steel plate ventilation pipes.
Details the process for conducting air tightness tests and vacuum drying.
Explains how to calculate and perform refrigerant charging, including pre-charging and start-up.
Outlines safety precautions related to refrigerant leakage and concentration limits.
Covers general notices, wiring rules, grounding, and electrical parameters.
Details the steps and procedures for connecting the power cord correctly.
Illustrates the external wiring diagram for the unit's electrical connections.
Guides on selecting communication cables and connecting them to terminals.
Shows connection methods between indoor units, controllers, and outdoor units.
Explains communication bus connection, address settings, and communication ports.
Lists essential checks to perform after installation before system operation.
Provides notes and preparations required before starting unit debugging and operation.
Details important notices and procedures to follow during unit debugging.
Explains the various stages, LED displays, and procedures for engineering debugging.
Lists reference values for key parameters to ensure normal unit operation.
Provides instructions on how to operate the air conditioner using controllers.
Details regular inspection and maintenance tasks for extending unit service life.
Covers precautions for starting usage and maintenance at the end of the season.
Lists common issues, their reasons, and recommended measures for resolution.
Details abnormal cooling/heating phenomena, non-malfunctions, and error codes.
Provides comprehensive lists of error codes for indoor, outdoor, and debugging.
Outlines warranty conditions and how to contact service for quality problems or inquiries.
To Next Page