PART NUMBER 177364, REV. C (10/20)
This manual provides information for:
STEAM JACKETED KETTLE
MODELS EE-20 & 40
(CE) INTERNATIONAL
EQUIPMENT DESCRIPTION
The EE is a floor-mounted, stationary,
steam jacketed kettle with an elec-
tronically controlled, self-contained,
electrically-heated steam supply and
appropriate controls, mounted on a
sturdy base. The kettle is available in
20 or 40 gallon (75 or 150 liters) ca-
pacities.
The body of the kettle is constructed of stainless steel, welded into one solid piece.
The kettle is furnished with 50 mm (2 in.) sanitary tangent draw-off valve (product
faucet) and a stainless steel strainer. Standard draw-off uses a compression disc
valve. Unit is provided with a one piece, hinged design dome style cover. It has a
steam jacket rated for working pressures up to 30 psi (206 kPa, 2.06 bar). Kettle
finish is 180 emery grit on the inside and #3 uniform finish on the outside.
The kettle is surrounded by insulated stainless steel sheathing. Stainless steel
panels enclose the controls. Three stainless steel, tubular legs support the unit.
Bullet feet on each of the legs can be adjusted to level the kettle.
A built-in steam generator, sized for the kettle capacity and heated by electric-
ity, delivers steam into the jacket. “Airless” operation of the steam jacket permits
uniform, efficient heating at temperatures as low as 150°F (65.5°C) and as high
as 270°F (132°C). In addition to the electronic temperature control, the unit has a
low water cut-off, safety valve, and high-limit pressure switch as safety features. A
heating indicator light, pressure gauge, and sight glass are provided for monitoring
kettle operation.
A single electrical connection is required for installation. The unit may be ordered
for use with 230 VAC, 1 Phase, 50 Hz, or 400 VAC, 3 Phase, 50 Hz power.
Options available include:
1. 75 mm (3 in.) diameter tangent draw-off (product valve) (factory installed)
2. Perforated or solid disc strainer
3. Water fill faucets
4. Basket cooking system
5. Kettle brush kit
6. Gallon etch marks (factory installed)
Information contained in this document is known to be current and accurate at the time of printing/creation. Unified Brands recommends
referencing our product line websites, unifiedbrands.net, for the most updated product information and specifications. © 2020 Unified Brands. All
Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.
REFERENCES
NSF INTERNATIONAL
798 N. Dixboro Rd.
P.O. Box 130140
Ann Arbor, Michigan 48113-0140
UNDERWRITERS LABORATORIES, INC.
333 Pfingsten Road
Northbrook, Illinois 60062
KLENZADE SALES CENTER ECOLAB, Inc.
370 Wabasha
St. Paul, Minnesota 55102
NATIONAL FIRE PROTECTION ASSOCIATION
60 Battery March Park
Quincy, Massachusetts 02269
NFPA/70 - The National Electric Code
ZEP MANUFACTURING COMPANY
1310-T Seaboard Industrial Boulevard
Atlanta, Georgia 30318
OPERATOR MANUAL
IMPORTANT INFORMATION, KEEP FOR OPERATOR
2016 Gees Mill Road, Suite 200, Conyers, GA 30013
888-994-7636, fax 888-864-7636
unifiedbrands.net
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ,
UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND WARNINGS CONTAINED
IN THIS MANUAL.
WARNING Improper installation, adjustment, alteration, service or
maintenance can cause property damage, injury or death. Read the
installation, operating and maintenance instructions thoroughly before
installing or servicing this equipment.
NOTIFY CARRIER OF DAMAGE AT ONCE It is the responsibility of the
consignee to inspect the container upon receipt of same and to determine
the possibility of any damage, including concealed damage. Unied Brands
suggests that if you are suspicious of damage to make a notation on the
delivery receipt. It will be the responsibility of the consignee to le a claim
with the carrier. We recommend that you do so at once.
Manufacture Service/Questions 888-994-7636.
To Next Page
Need help?
General
