GRS GraverMax G8 - SETUP & CONNECTIONS; MOUNT & CONNECT AIR FILTER; CONNECT FOOT THROTTLE; CONNECT HANDPIECE(S)

7
MOUNT & CONNECT AIR FILTER
4V\U[HPYÄS[LYPUHSVJH[PVU^OLYL[OLHPY
ÄS[LYTH`ILKYHPULKKHPS`ZLL-0.(
Refer to FIG. 2 for instructions on
TV\U[PUN[OLHPYÄS[LY[VZPKLVMZ`Z[LT
Power off engraving system and air
supply. Insert appropriate hose (see
-0.PU[V[OLÄ[[PUN\U[PS[OLOVZL
stops and is secure. Power on engraving
system and air supply to check for leaks
and improper connections; air should
UV[LZJHWL[OYV\NOHU`OVZLVYÄ[[PUN
If air leaks, power off system and air
supply. Locate leaks and correct any
improper connections. To disconnect
MYVTHW\ZO[VJVUULJ[Ä[[PUNWYLZZPU
on the orange ring while gently pulling
out the hose.
CONNECT FOOT THROTTLE
7SHJLMVV[[OYV[[SLVU[OLÅVVYPUH
convenient position. Extend throttle
hose to back of system (FIG. 3.D) to
PUZLY[PU[VÄ[[PUNTHYRLK¸;/96;;3,
CONNECTION”. The hose should not
be pinched or kinked.
NOTE: The foot
throttle varies handpiece power by
JVU[YVSSPUN[OLHTV\U[VMHPY[OH[ÅV^Z
from the handpiece. While the throttle
is depressed, it is normal for air to be
released. The user may hear the air
being released at times during operation.
CONNECT HANDPIECE(S)
Two handpieces may be connected;
only one handpiece can be in operation
at any time. Each Standard Handpiece
\ZLZHZPUNSLW\ZO[VJVUULJ[Ä[[PUN
(FIG. 3.A).
Connect desired handpiece(s)
accordingly. The handpiece selector
RUVIHIV]L[OLÄ[[PUNZHSSV^Z\ZL
of either handpiece 1 or handpiece
2 (FIG. 1.E).
NOTE: The handpiece
selector knob line should point to the
ZLSLJ[LKÄ[[PUN
USING AN AIR-DRIVEN ROTARY
HANDPIECE
;OLH\_PSPHY`W\ZO[VJVUULJ[Ä[[PUN
-0.)PZHZ[YHPNO[ÅV^HPYWVY[[OH[
is limited to 40 psi (2.7 bar) maximum.
;OPZPZ[OLÄ[[PUNMVYHYV[HY`OHUKWPLJL
or other pneumatic tool. The knob is a
[^PZ[VWLU[^PZ[JSVZL]HS]LVU[OLMYVU[
of system (FIG. 1.G).
DO NOT EXCEED 35 psi (2.4 bar)
when using the GRS Ultra 850
Rotary Handpiece.
CONNECT ELECTRICAL POWER
DO NOT OPERATE
ENGRAVING SYSTEM
WITHOUT AN ACTIVE AIR SUPPLY
CONNECTED.
Insert the converter cord
into receptacle on engraving system
(FIG. 3.E and F). Connect the electrical
power cord into the 24-volt power
converter. Connect the 3-prong power
cord into a properly grounded power
outlet, using adapters as needed.
See pages 2-3 for details.
SETUP & CONNECTIONS