EasyManua.ls Logo

H3C MSR Series

H3C MSR Series
28 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
22
*Nov 7 09:23:15:524 2014 ROUTER IKE/7/DEBUG: exchange state machine(I): finished step
2, advancing...
//Phase 1 negotiation finished.
…………………
*Nov 7 09:23:21:801 2014 ROUTER IKE/7/DEBUG: send message:
//The device sent the first packet for the phase 2 negotiation.
*Nov 7 09:23:21:902 2014 ROUTER IKE/7/DEBUG: ICOOKIE: 0xb8a20d7c014806fa
*Nov 7 09:23:22:002 2014 ROUTER IKE/7/DEBUG: RCOOKIE: 0x67a9145eb46c41d9
…………………
*Nov 7 09:23:22:506 2014 ROUTER IKE/7/DEBUG: exchange state machine(I): finished step
0, advancing...
*Nov 7 09:23:22:606 2014 ROUTER IKE/7/DEBUG: received message:
//The device received a reply packet from the peer.
*Nov 7 09:23:22:657 2014 ROUTER IKE/7/DEBUG: ICOOKIE: 0xb8a20d7c014806fa
*Nov 7 09:23:22:757 2014 ROUTER IKE/7/DEBUG: RCOOKIE: 0x67a9145eb46c41d9
…………………
*Nov 7 09:23:24:571 2014 ROUTER IKE/7/DEBUG: validate payload NOTIFY
*Nov 7 09:23:24:621 2014 ROUTER IKE/7/DEBUG: DOI: IPSEC
*Nov 7 09:23:24:722 2014 ROUTER IKE/7/DEBUG: PROTO: IPSEC_ESP
*Nov 7 09:23:24:822 2014 ROUTER IKE/7/DEBUG: SPI_SZ: 4
*Nov 7 09:23:24:873 2014 ROUTER IKE/7/DEBUG: MSG_TYPE: INVALID_ID_INFORMATION
//The device received a reply packet of the INVALID_ID_INFORMATION type. The negotiation
failed.
*Nov 7 09:23:24:973 2014 ROUTER IKE/7/DEBUG: exchange setup(R): 9c16530
*Nov 7 09:23:25:024 2014 ROUTER IKE/7/DEBUG: exchange check: checking for required
INFO
*Nov 7 09:23:25:124 2014 ROUTER IKE/7/DEBUG: got NOTIFY of type
INVALID_ID_INFORMATION
The previous debugging information shows that packet exchanges were normal in phase 1
negotiation. In phase 2 negotiation, however, the initiator received an
INVALID_ID_INFORMATION packet from the peer. This packet resulted in the IPsec SA
negotiation failure. We need to identify why the peer device (the receiver) sent such a packet.
2. On the receiver, display IKE debugging information by using the debugging ike all
command. The key debugging information is as follows:
*Nov 6 17:03:05:527 2014 ROUTER IKE/7/Event: IKE thread 366519722672 processes a job.
*Nov 6 17:03:05:527 2014 ROUTER IKE/7/Packet: Begin a new phase 1 negotiation as
responder.
*Nov 6 17:03:05:527 2014 ROUTER IKE/7/Event: Responder created an SA for peer 10.1.1.1,
local port 500, remote port 500.
*Nov 6 17:03:05:527 2014 ROUTER IKE/7/Event: Set IKE SA state to IKE_P1_STATE_INIT.
*Nov 6 17:03:05:527 2014 ROUTER IKE/7/Packet: Received ISAKMP Security Association
Payload.
//The device received the first negotiation packet from the peer.
………
*Nov 6 17:03:05:527 2014 ROUTER IKE/7/Packet: The profile 1 is matched.

Other manuals for H3C MSR Series

Related product manuals