11-4
displayed in the ways shown in Table 11-1. The meanings of the parameters in the configuration column
are as follows:
z 1 indicates date-time has been configured with the clock datetime.
z 2 indicates time-zone has been configured with the clock timezone command and the offset time
is zone-offset.
z 3 indicates daylight saving time has been configured with the clock summer-time command and
the offset time is summer-offset.
z [1] indicates the clock datetime command is an optional configuration.
z The default system clock is 2005/1/1 1:00:00 in the example.
Table 11-1 Relationship between the configuration and display of the system clock
Configuration
System clock displayed by
the display clock command
Example
1
date-time
Configure: clock datetime 1:00 2007/1/1
Display: 01:00:00 UTC Mon 01/01/2007
2
The original system clock ±
zone-offset
Configure: clock timezone zone-time add 1
Display: 02:00:00 zone-time Sat 01/01/2005
1 and 2 date-time ± zone-offset
Configure: clock datetime 2:00 2007/2/2 and clock
timezone zone-time add 1
Display: 03:00:00 zone-time Fri 02/02/2007
[1], 2 and 1
date-time
Configure: clock timezone zone-time add 1 and clock
datetime 3:00 2007/3/3
Display: 03:00:00 zone-time Sat 03/03/2007
If the original system clock is not
in the daylight saving time
range, the original system clock
is displayed.
Configure: clock summer-time ss one-off 1:00 2006/1/1
1:00 2006/8/8 2
Display: 01:00:00 UTC Sat 01/01/2005
3
If the original system clock is in
the daylight saving time range,
the original system clock +
summer-offset is displayed.
Configure: clock summer-time ss one-off 00:30 2005/1/1
1:00 2005/8/8 2
Display: 03:00:00 ss Sat 01/01/2005
If date-time is not in the daylight
saving time range, date-time is
displayed.
Configure: clock datetime 1:00 2007/1/1 and clock
summer-time ss one-off 1:00 2006/1/1 1:00 2006/8/8 2
Display: 01:00:00 UTC Mon 01/01/2007
1 and 3
If date-time is in the daylight
saving time range, “date-time” +
“summer-offset” is displayed.
Configure: clock datetime 8:00 2007/1/1 and clock
summer-time ss one-off 1:00 2007/1/1 1:00 2007/8/8 2
Display: 10:00:00 ss Mon 01/01/2007
If date-time is not in the daylight
saving time range, date-time is
displayed.
Configure: clock summer-time ss one-off 1:00 2007/1/1
1:00 2007/8/8 2 and clock datetime 1:00 2008/1/1
Display: 01:00:00 UTC Tue 01/01/2008
Configure: clock summer-time ss one-off 1:00 2007/1/1
1:00 2007/8/8 2 and clock datetime 1:30 2007/1/1
Display: 23:30:00 UTC Sun 12/31/2006
[1], 3 and 1
date-time is in the daylight
saving time range:
If the value of “date-time” -
“summer-offset” is not in the
summer-time range, “date-time”
- “summer-offset” is displayed;
If the value of “date-time” -
“summer-offset” is in the
summer-time range, date-time
is displayed.
Configure: clock summer-time ss one-off 1:00 2007/1/1
1:00 2007/8/8 2 and clock datetime 3:00 2007/1/1
Display: 03:00:00 ss Mon 01/01/2007
To Next Page
Loading...
