168
(
1) Press the mode key to switch to the dry mode, and the
humidity will be shown in the temp. display area. The Up/Down
key is the humidity adjusting key.
(2) If Sw2 is set to be on, the temp. display area will display
the ambient temp. in all modes except for the dry mode,
which will display the ambient humidity. When in the state of
OFF→ON, mode shift to dry mode, set humidity adjustment in
dry mode, the set hum. will display statically, SET icon
and after 3s, ambient hum. and ROOM icon display statically.
Humidity Function (Only valid for part of models)
When cleaning icon is displayed, the icon will display
in function sequence. If
cleaning icon is press
key to clear it.
Filter Cleaning
(1) Press key to enter function setting, then press
to choose energy saving, press
key again to the
operation and display energy saving icon
. If energy
saving function has been set, the above operation will cancel
it.
(2)The energy saving default parameter are 23°C (74°F) (the
lowest temp. limit of cooling and dry mode) and 26°C (78°F)
(the highest temp. limit of heating mode). The temp. adjusting
range is 23°C-30°C (74°F-80°F) in cooling and dry mode, the
temp. adjusting range is 16°C-26°C (60°F-78°F) in heating
mode. If energy saving function is set, the indoor units will run
at the default temperature.
Note: Fresh Air unit has no energy saving function.
Energy Saving
(1) Only in heating mode, this function is valid in function
circulation.
(2) For the four-way cassette model, press the SET key for
5s to enter the function circulation. When it switches to the
10°C heating function, 10°C will
in the temp. display
area. Press the SET key to
and 10°C will be statically
displayed.
(3) If the wired controller receives the signal of 10°C heating
function sent by the remote controller, 10°C will be statically
displayed in the temp. display area of the wired controller.
(4) If the wired controller is displaying room temp., when
the 10°C heating function is set. The 10°C will be statically
displayed for 3s ,then it changes to display room temp.. If the
temp. area displays room temp., press the Up/Down key
the 10°C heating icon will be displayed. Press the Up/Down key
again, exit the 10°C heating function. Meanwhile, the set temp.
will be displayed statically, at this moment, the SET character
for 3s, then the room temp. and ROOM character
displays. Press the mode key to change the mode directly, and
at the same time exit the 10°C heating function; press the Fan
key or Time key, the command will be executed; press the Set
key and the Up/Down key to switch to the 10°C function, press
the function key again, the function will be canceled.
10°C Heating Function (Only valid for part of models)
(5) If it’s not the four-way cassette model, press the Set key
once to enter the function circulation. When it switches to the
10°C heating function, the temp. display area will statically
display 10°C. Then press the Set key to
The exist
operations will be the same as the four-way cassette model.
(6) This function can be remembered when it is turned on/off.
(1) When it is powered on for the
time, four-way cassette
icon and Up/Down swing will be displayed. The number1,2,3,4
next to the swing referred to different wind
will be
displayed(if the wind
is on the position 1, the Up/
Down swing will stay the angle set by the wind
position 1.Meanwhile the number 1 next to the Up/Down
swing will be displayed. If it is selected as four sides controlled
together, the number 1, 2, 3 ,4 next to the Up/Down swing will
be displayed at the same time). Set key now can only switch
among four wind
Use Up/Down key to set the angle
of the current wind
Four-way cassette - Function (Only valid for part of
models)
(2) The circulation of the wind
four-way cassette controlled together→four-way
cassette
1→four-way cassette 2→four-way
cassette
3→four-way cassette 4→four-way
cassette
controlled together.
(3) If it’s not the
time to enter it, press Set key, the wind
set last time will Meanwhile the angle of this
set last time will be displayed statically, and the
number of the wind
next to Up/Down swing will be
statically displayed.
(4) Press Set key to choose the wind
and the
selected one will
At this time press Up/Down key to
adjust the angle of the wind
The wind will
keep
when adjusting. After adjusting for
5s, the wind
will be displayed statically, meaning
existing the angle adjustment. At this time press Up/Down
key to adjust the temp.. Pressing mode key or Fan key during
the adjustment will exist the adjustment of four-way cassette
function. The position and angle of the wind
will be
set the same as last time. If no pressing Up/Down key for 5s
after Set key pressed, the selected wind
will stop
and go back to the previous state.
To Next Page
Loading...
