169
(1) For the four-way cassette model, press the SET key for
5s to enter the function circulation (if it is not the four-way
cassette model, press the SET key once to enter the function
circulation), and then press Up/Down key to switch to
(the
second 8 of 88.8 in the temp. display area displaying A) →
(the second 8 of 88.8 in the temp. display area displaying B)
→
(motion sensing).
(2)
①
After motion sensing A is set, the character A will
disappear with room temp./set temp. displaying. The icon of
motion sensing will display statically.
②
After motion sensing B is set, the character B will disappear,
with room temp./set temp. displayed. The icon of motion
sensing will
in the frequency.
③
After motion sensing is set, the icon of motion sensing
will be displayed for 2s and disappear for another 2s to have
respiratory effect.
Motion sensing (Only valid for part of models)
(1) In off and non screen saving state, press Mode key for 5s,
it will display 8 segment on the top-left corner of current mode
circulation, default value being 0. Press Up/Down key to shift
between 0, 1, 2, 3, then press Set key to
value. It will
follow the altered mode circulation after turning on the unit
again.
Corresponding mode of different value.
0-------------[Intelligent] [Heating] [Dry] [Cooling] [Fan]
1-------------[Heating] [Dry] [Cooling] [Fan]
2-------------[Dry] [Cooling] [Fan]
3-------------[Heating] [Dry] [Cooling] [Fan]
(2) If modes are reduced and the mode that is set before
turning off is not in the newly set mode circulation, the initial
mode is fan.
(3) The intersection of mode circulation set by wired controller
and indoor unit is valid.
(4) Fresh Air unit can execute mode setting, it will execute
the intersection with three modes of Fresh Air unit (cooling/
heating/fan mode)
(5) This setting is ground
setting and will be memorized
whether non-volatile memory invalid or valid.
Mode Setting (Only valid for part of models)
(6) The mode of indoor units can be inquired /changed by the
advanced setting function after the wired controller is powered
on, Only valid for part of models.
(7) Set as follows (Only valid for part of models):
Press Set key and Up key for 5s to enter the advanced setting
state, with the function A in temp. display area displayed
statically. Press Fan key to switch to function B. The function
code 01 displayed in the clock display area will The
information in the timing display area is statically
displayed, it can be changed in the range of 00-03 by Up/
Down key. At this time press Set key to
and the
function code 01 in clock display area stays static, the
information in the timing display area
meaning it can
be changed currently. Press Up/Down key to change the
content and Set key to
(8) If the mode is changed from more to less, the current mode
will not be in the mode of the present circulation. It will be the
fan mode after turn on.
(1) The main interface does not display malfunction.
(2) Under no screen saving state, press
key for 10
seconds to check all indoor units malfunction in the group, but
at this time, the interface does not display clock information
and timer information. Unit No. is displayed behind the top-left
colon; current malfunction is displayed before top-right colon
and historical malfunction is behind colon.
(3) Unit No. is displayed in decimal and malfunction is
displayed in hexadecimal.
(4) All hexadecimal numbers of malfunction are in capital. But
b and d is in small capital in order not to mix with 8.
(5) If there is no current malfunction, “--” is displayed before
the right colon; if there is no historical malfunction, “--” is
displayed behind the right colon.
(6) Press
key to quit malfunction check state. The clock
information and timer information are displayed.
(7) Malfunction records clearance: Keep pressing
key for
10 seconds, malfunction is displayed. Then press
key
again for 5 seconds to clear current and historical malfunction
of all the units.
(8) Press
to choose unit No..
Malfunction Display
To Next Page
Loading...
