Why is the suction pressure high in my Haier Air Conditioner?
High suction pressure in your Haier Air Conditioner can be caused by: * Too high charge of refrigerant, so you should adjust the charge of refrigerant. * High water inlet temperature at the water side, so you should check the water temperature. * High ambient temperature of the air-side heat exchanger, so you should inspect the ambient temperature.
What to do if my Haier CA0035EAND has low suction pressure?
If your Haier Chiller has low suction pressure, it could be due to insufficient refrigerant (adjust the charge), a faulty low-pressure switch (replace it), insufficient water flow (check the water flow), low water inlet temperature at the water side (check the water temperature), scaling or foreign matter inside the water-side heat exchanger (clean up the incrustation scale), insufficient air capacity (check the fan), a short circuit in the air circuit (check the cause and troubleshoot), or incomplete defrosting (replace the poor 4-way valve or defrosting sensor).
What causes an open or short circuit in the temperature sensor of a Haier Air Conditioner?
An open or short circuit in the temperature sensor of your Haier Air Conditioner may be due to: * Damaged sensor: Replace the sensor. * Poor connection of sensor: Reconnect the sensor.
What to do if there is a fault in communication of the wired controller of my Haier Air Conditioner?
A fault in the communication of the wired controller for your Haier Air Conditioner can be caused by: * Incorrect unit numbering: Check the unit numbering and correct it. * Incorrect connection of communication wires: Check the order of connection of communication wires. * Damaged PCB: Replace the PCB. * Poor wired controller: Replace the wired controller.
Why is the exhaust temperature sensor overheating on my Haier Air Conditioner?
Overtemperature of the exhaust temperature sensor in your Haier Air Conditioner may be caused by: * Poor ventilation around the unit: Clean up obstacles or add air ducts. * Too low ambient temperature: Shut down the unit. * Dirty or clogged filter at the fluorine side: Replace the filter. * Incomplete frosting (for heating) or no frosting: Change the frosting parameters.
What causes a fault in the flow switch of my Haier Air Conditioner?
A fault in the flow switch of your Haier Air Conditioner can occur due to: * Air in the water system: Discharge air via the exhaust valve. * Water-side heat exchanger scaling or foreign matter inside: Clean up the incrustation scale. * Poor switch: Replace the target flow switch. * Unevenly distributed flow in water pipelines: Adjust the flow in water pipelines via the shut-off valve. * Out-of-service water pump: Machine installation must be ganged. * Insufficient types of water pumps: Check it and try to fix it.
What causes an over-current fault in the compressor of a Haier Air Conditioner?
An over-current fault in the compressor of your Haier Air Conditioner may be due to: * High exhaust pressure and high suction pressure: Refer to “High Exhaust Pressure” and “High Suction Pressure”. * High or low voltage, single phase or phase imbalance: Check the power supply. * Short circuit in motor or terminal: Check the terminal connections.
What to do if the exhaust pressure is too low on my Haier Air Conditioner?
Too low exhaust pressure in your Haier Air Conditioner can be caused by: * Lack of refrigerant: Adjust the charge of refrigerant. * Low suction pressure: Refer to “Low Suction Pressure”. * Low ambient temperature of the air-side heat exchanger: Check the ambient temperature. * Too low water temperature at the water side: Check the water temperature.
How to fix abnormal noise in Haier Air Conditioner?
Abnormal noise in your Haier Air Conditioner can be caused by: * Loose metal plate bolts: Retighten the bolts. * Liquid impact due to entry of liquid refrigerant into the compressor: Adjust the charge of refrigerant or the poor throttling device. * Poor compressor: Replace the compressor.
What causes low suction pressure in my Haier Air Conditioner?
Low suction pressure in your Haier Air Conditioner may occur due to: * Insufficient refrigerant: Adjust the charge of refrigerant. * Undesirable low-pressure switch: Replace the low-pressure switch. * Insufficient water flow: Check the water flow. * Low water inlet temperature at the water side: Check the water temperature. * Water-side heat exchanger scaling or foreign matter inside: Clean up the incrustation scale. * Insufficient air capacity: Check the fan. * Short circuit in the air circuit: Check the cause of the short circuit and troubleshoot. * Incomplete defrosting: Replace the poor 4-way valve or defrosting sensor.
Details the unit's features, applications, reliability, safety, and adaptability.
Explains how the unit uses advanced technology for efficient operation and energy savings.
Describes the unit's electronic controller for centralized and independent operation.
Highlights the unit's design for simplified installation and space efficiency.
Covers the unit's safety features like pressure protection and anti-freezing.
Mentions easy access to parts for maintenance and troubleshooting.
Explains the meaning of warning and caution symbols used in the manual.
Provides critical safety information regarding installation and maintenance by professionals.
Advises on proper installation locations and operational precautions to avoid damage.
Details the physical layout and components of the wired controller interface.
Explains the function of each button on the wired controller for system operation.
Guides on starting up, operating modes, and temperature adjustments using the controller.
Explains how to interpret information displayed on the controller's main interface.
Instructions for setting up daily startup and shutdown schedules for the week.
Instructions for setting up cyclical startup and shutdown schedules.
Instructions for setting up daily specific startup and shutdown times.
Explains how to disable the unit's timing functions.
Provides dimensional drawings and measurements for the CA0035EAND unit.
Guidelines for designing and preparing the unit's installation base.
Illustrates the base mounting points and dimensions for unit installation.
Shows base mounting details for CA0070EAND, CA0100EAND/CA0130EAND units.
Covers essential steps like cargo inspection, handling, and disassembly before installation.
Provides criteria for selecting an optimal and safe installation location.
Shows the required clearance and space for installing a single chiller unit.
Illustrates the necessary spacing for installing multiple chiller units together.
Provides visual guidance on the physical layout of multiple chiller units.
Details the procedures and requirements for connecting the unit's water piping system.
Specifies the acceptable water quality parameters for system operation.
Presents a visual representation of the water system components and connections.
Outlines fundamental requirements for setting up the chilled water pipeline system.
Provides instructions and safety guidelines for connecting the unit's electrical wiring.
Lists pre-operation checks to ensure safe and correct system setup.
Details specific checks required before the initial startup of the unit.
Describes how to monitor and check the unit's performance during operation.
Table showing nozzle dimensions based on the number of modules combined.
Guides on calculating the necessary water capacity for the system.
Provides recommendations for selecting auxiliary heaters for specific conditions.
Illustrates the wiring connections for the unit's power supply cords.
Table listing essential electrical specifications for different unit models.
Instructions for setting the address codes for modular units.
Specifies the standards and characteristics for communication cables.
Shows the wiring diagram for connecting communication wires between units.
Procedure for inspecting and cleaning the unit's condenser fins.
Steps for checking and cleaning the water-side heat exchanger.
Information regarding refrigerant and lube oil levels and replenishment.
List of error codes, their descriptions, and remarks for troubleshooting.
Details common operational issues and their corresponding solutions.
Table summarizing key performance specifications for various unit models.
Provides correction factors for performance based on operating conditions.
Defines the operating range and conditions for the chiller unit.
To Next Page
General