Haier GE DD02-18 - User Manual

Service Bulletin
DD02-18
CSM (Current Sense Module) Causes No Operation or
Dead Condition
Dishwasher
A heating element or random non dishwasher faults may cause the CSM to trip and render a
dishwasher in a no operation or dead state. For the models and serials shown, follow these
instructions.
Plastic Tub Models
ADT521PGF6
ADT521PGJ(0-12)*
GDF510P_D6
GDF510P_J(0-5)*
GDF520P_D6
GDF520P_F6
GDF520P_J(0-5)*
GDF540H_D6
GDF540H_F6
GDF610P_J(0-5)*
GDF620H_J(0-5)*
GDT530P_D6
GDT535P_J(0-5)*
GDT545P_J(0-5)*
GDT550H_D6
GDT625P_J(0-5)*
GDT635H_J(0-5)*
SS Tub Models
CDT725SSF(6-7)SS
CDT765SSF7SS
CDT835S_J(0-2)*
CDT865S_J(0-2)*
DDT575S_F(6-8)*
DDT595S_J(0-2)*
GDF570S_F(6-8)*
GDF570S_J(0-2)*
GDF650S_J(0-2)*
If the dishwasher has no response, no LED’s,
display or operation, the CSM may be
tripped.
GE Technicians use laptop diagnostics to
diagnose
CC Technicians will enter Consumer Error
Mode.
Press the Select Cycle and Start buttons at
the same time for Five (5) seconds. If the
control responds with LED’s or Display
coming on, The CSM is tripped.
Or
Access the main control board and view the
service LED. If it is flashing 7 times within 3
seconds, the CSM is tripped.
Models affected:
Serial numbers:
Replace the Heating Element with
WD05X24776* and update the software.
GE Technicians will use laptop diagnostics to
diagnose and update software.
Customer Care Technicians will use
Consumer error and Service Modes to
diagnose and SUM Module WD98R2327901
to update software.
Follow the steps on the next page
Important Note: All components must be
thoroughly dry when installing the new
element, including the tub area around the
element (inside and outside).
* Exposed Heater models only
May 2018 (Supersedes DD02-17)
HF – GL (May 2015 – April 2018)
Diagnosis:
Repair:
SS Tub Models
(continued)
GDT580S_F(6-8)*
GDT590S_J7*
GDT655S_J(0-2)*
GDT655S_L(2-3)*
GDT680S_H(6-8)*
GDT695S_J(0-2)*
GDT695S_L(2-3)*
GDT740SIF(7, 8, A)II
PDF820S_J(02)*
PDT720S_H(6-7)*
PDT750S_F(7, 8, A)*
PDT760S_(F, J)7*
PDT825S_J(0-2)*
PDT845S_J(0-2)*
PDT845S_L(2-3)*
PDT846S_J(0-2)*
PDT855S_J(0-2)*
PDT855S_L(2-3)*
ZDT800S_F7
ZDT870S_F7
ZDT915S_J(0-2)*
ZDT975S_J(0-2)*
1
* If model number includes (parentheses), it
indicates all engineering digits in that range
or model design year.

Summary

Dishwasher CSM Fault Diagnosis and Repair

CSM Causes No Operation or Dead State

A tripped CSM can cause a dishwasher to be in a no operation or dead condition.

Affected Models and Serial Numbers

Lists specific GE dishwasher models and serial number ranges affected by this CSM issue.

Diagnosis Procedures

Details initial methods to diagnose a tripped CSM, checking for no response or display issues.

Repair and Software Updates

Outlines replacing the Heating Element and updating software to resolve CSM-related faults.

Detailed CSM Reset and Diagnostic Flow

Entering Service Mode

Steps to enter Consumer Error Mode and then Service Mode for diagnostics and tests.

CSM Tripped Troubleshooting Flowchart

Visual guide for diagnosing CSM trips, checking for leaks, and testing components.

Component Testing and Repair Actions

Actions for CSM trips related to circulation pump, drain pump, heater, or main control.

Haier GE DD02-18 Specifications

General

Brand	Haier
Model	GE DD02-18
Category	Dishwasher
Language	English