Hakko Electronics FR-400 - Page 19

● Auto Sleep
1.
Move the cursor to select “ Auto Sleep ”.
After selecting, press <ENT>.
Select whether you will activate the auto sleep function. When the auto sleep function is
set to on and no operation is performed for constant time after the handpiece is set in
the iron holder, the auto sleep function will be enabled and the temperature of the
handpiece declines to the controlled degree.
*
The auto sleep temperature can be set in “Sleep Temp”.
2. ON and OFF will be switched alternately
if you press the <↑> or <↓> button.
3. Selecting “ON” allows you to make the
setting for “Timer”.
(Default is 6 minutes.)
* When selecting “ON”
4. When setting “Auto Sleep” to “ON”,
the area for Timer flashes.
5. Press the <↑> or <↓> button, you can
change to the desired value.
6. Pressing the <ENT> button after this change
makes the set time stored in the internal
memory.
<↑> <↓> <ENT>
S h u t O f f S e t
V acuumM o d e
A uto S l e ep
OFF
NOR
OFF
<↑> <↓> <ENT>
 A uto S l e ep S e t
A uto S l e ep OFF
T i m e r 06m
<↑> <↓> <ENT>
 A uto S l e ep S e t
A uto S l e ep ON
T i m e r
6m
Select
“OFF”
Select
“ON”
<↑> <↓> <ENT>
S h u t O f f S e t
V acuumM o d e
A uto S l e ep
OFF
NOR
06m
17
6. PARAMETER SETTING (continued)
● Sleep Temp
● Low Temp
1.
Move the cursor to select “ SleepTemp ”.
After selecting, press <ENT>.
Sets the auto sleep temperature.
When the temperature drops below a set limit, an error is displayed and the buzzer
sounds.
2. Entering from hundreds to units digit.
Press the <↑> or <↓> to set the desired
figure.
You will proceed to the next digit if the
<ENT> button is pressed.
Only values from 2 to 3 can be selected when
entering the hundreds digit.
(In °F mode, values from 3 to 5 can be selected.)
Values from 0 to 9 can be selected when
entering the tens or units digits.
(The same values can be selected in °F mode.)
2. Entering from hundreds to units digit.
Press the <↑> or <↓> to set the desired
figure.
You will proceed to the next digit if the
<ENT> button is pressed.
Only values from 0 to 1 can be selected when
entering the hundreds digit.
(In °F mode, values from 0 to 2 can be
selected.)
Values from 0 to 9 can be selected when
entering the tens or units digits.
(The same values can be selected in °F mode.)
3. After entering the units digit, press the button
to save the figure to the system memory
1. Move the cursor to select “ Low Temp ”.
After selecting, press <ENT>.
3. After entering the units digit, press the button
to save the figure to the system memory.
<↑> <↓> <ENT>
V acuumM o d e
A uto S l e ep
S l e e p T emp
NOR
06m
200ﾟ C
<↑> <↓> <ENT>
S l e e p T emp S e t
00ﾟ C
<↑> <↓> <ENT>
A uto S l e ep
S l e e p T emp
L o w Temp
06m
200ﾟ C
150ﾟ C
<↑> <↓> <ENT>
L o w T emp S e t
50ﾟ C
18