Hameg HM8118 User Manual

39
Content
1 Important Notes .......................40
1.1 Symbols ..................................40
1.2 Unpacking .................................40
1.3 Setting Up the Instrument ....................40
1.4 Safety ....................................40
1.5 Intended Operation ..........................40
1.6 Ambient Conditions .........................41
1.7 Warranty and Repair .........................41
1.8 Maintenance ...............................41
1.9 Line fuse ..................................41
1.10 Power switch ..............................41
1.11 Batteries and Rechargeable Batteries/Cells .......41
1.12 Product Disposal ............................42
2 Description of the Operating Elements .....43
3 Introduction ..........................45
3.1 Requirements ..............................45
3.2 Measurement of a capacitor ..................45
3.3 Measurement of an inductor ..................45
4 First-Time Operation .................... 46
4.1 Connecting the instrument ....................46
4.2 Turning on the instrument ....................46
3.4 Measurement of a resistor ....................46
4.3 Line frequency .............................47
4.4 Measurement Principle .......................47
4.5 Measurement Accuracy ......................48
5 Setting of Parameters ..................49
5.1 Selecting Values /Parameters ..................49
6 Measurement Value Display. . . . . . . . . . . . . . 50
6.1 Relative Measurement Value Deviation ∆ %
(#, %)
.....................................50
6.2 Absolute Measurement Value Deviation ∆ ABS (#) .50
5.2 Selecting the Measurement Function ...........50
6.3 Reference Value (REF_M, REF_S) ...............51
6.4 Selecting the Measurement Range .............51
6.5 Circuit Type ................................52
7 Instrument Functions ...................52
7.1 SETUP Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
7.1.1 Measurement Frequency FRQ
.................52
7.1.2 Voltage LEV ...............................53
7.1.3 Preload/ Bias Current BIAS ...................53
7.1.4 Measurement Range RNG ....................54
7.1.5 Measurement Speed SPD ....................54
7.1.6 Triggering TRIG ............................55
7.1.7 DELAY Function ............................55
7.1.8 Average Value AVG ..........................55
7.1.9 Display of Test Signal Level Vm (Measurement Vol-
tage) / Im (Measurement Current):
..............55
7.1.10 Guarding GUARD ...........................55
7.1.11 Deviation DEV_M ...........................56
7.1.12 Reference REF_M ...........................56
7.1.13 Deviation DEV_S ............................56
7.1.14 Reference REF_S ...........................56
7.1.15 CONSTANT VOLTAGE CST V ..................56
7.2 CORR Menu ...............................57
7.3 Menu Function SYST ........................58
7.4 Saving / Loading of Settings ..................59
7.5 Factory Settings ............................59
8 Measuring Equipment ..................60
8.1 4-Wire Test Adapter HZ181 (Including Short Circuit
Board) ....................................60
8.2 Kelvin-Test Lead HZ184 ......................61
8.3 4-wire Transformer Test Lead HZ186 ............61
8.4 4-Wire SMD Test Adapter HZ188 ...............63
8.5 Sorting Components with Option HO118 Binning
Interface
..................................64
9 Remote Control .......................66
8.1 RS-232 ....................................66
8.2 USB / VCP .................................67
8.3 IEEE-488 (GPIB) ............................67
10 Command Reference ...................68
10
.1 Setting Up the Command Structure ............68
10
.2 Supported Command and Data Formats .........68
10
.3 Command List Binning Interface ...............71
11 Technical Data ........................72
Content

Hameg HM8118 Specifications

General

Brand	Hameg
Model	HM8118
Category	Measuring Instruments
Language	English