Why does my Handicare Puma 20 show a low battery error?
A low battery error on your Handicare Wheelchair indicates that the control system has detected a battery voltage below 16V. Check the condition of the batteries and their connections to the control system. If the error persists after checking the batteries and connections, the Power Module may be defective.
What to do if my Handicare Wheelchair ON/OFF light doesn't turn on and it won't move?
If the ON/OFF light doesn't illuminate and the wheelchair remains stationary, several factors could be at play. First, ensure the controller plug is correctly inserted into the power module. Additionally, inspect the fuses and replace any that are defective. Verify that the batteries are properly connected and that all connections are secure. If this is a 'STALL' timeout, place the joystick in neutral and try again.
What does it mean if ON/OFF light flashes once on Handicare Mobility Aid?
If the ON/OFF light on your Handicare Mobility Aid flashes once, it indicates a faulty DX module. Replace one or more modules. The 'on/off' LED indicates the condition of the entire system, while each module has a separate status LED to help identify the faulty one.
How to fix service indicator flashes once on Handicare Mobility Aid?
If the service indicator flashes once on your Handicare Mobility Aid, it's likely a 'STALL' timeout due to user error. Place the joystick in neutral and try again.
Why ON/OFF light flashes 7 times on Handicare Mobility Aid?
If the ON/OFF light on your Handicare Mobility Aid flashes 7 times, it indicates a low battery voltage, or the batteries are flat or bad. Charge or replace the batteries. Note that if the voltage is low (less than 12V), the electronics won't work properly, and random LEDs of the DX controller may flash, preventing the wheelchair from functioning.
What does 'Left Indicator Lamp Failed' mean on my Handicare Puma 20 and how do I fix it?
A 'Left Indicator Lamp Failed' error indicates the control system has detected a failure in either of the Indicator Circuits. Check the indicator bulbs, cables, and connections to the control system. If the error persists, the ISM may be defective.
What to do if my Handicare Scooter ON/OFF light doesn't turn on and the wheelchair won't move?
If the ON/OFF light doesn't illuminate and the Handicare Scooter remains stationary, consider these potential causes and solutions: * Ensure the controller plug is correctly inserted into the power module. It may be a stall timeout, place the joystick in neutral and try again. * Inspect the fuses and replace any that are defective. * Verify that the batteries are properly connected. * Check for loose battery connections and secure them.
What does it mean when the ON/OFF light flashes 12 times on my Handicare Puma 20 Wheelchair?
If the ON/OFF light flashes 12 times, it indicates that the system does not 'fit' because the system modules are not compatible. Program the entire drive system for the relevant wheelchair using the DX-Wizard program on a PC. Always confirm the programming by switching the wheelchair on and off.
What does it mean when the ON/OFF light flashes twice on my Handicare Puma 20 Wheelchair?
If the ON/OFF light flashes twice, it could mean the DX accessory is faulty due to a programming fault or short circuit/overload of the accessories. Alternatively, if the electrical high/low adjustment is not in the lowest position, the LED will flash twice to indicate that the speed limitation has been switched on, causing the wheelchair to drive more slowly.
What does it mean when the ON/OFF light flashes once on my Handicare Puma 20?
If the ON/OFF light flashes once, it indicates that the DX module is faulty. Replace one or more modules. The 'on/off' LED indicates the condition of the entire system. The modules all have a separate status LED: in this way, you can see which one is faulty.
General| Type | Power Wheelchair |
|---|---|
| Foldable | No |
| Footrests | Yes |
| Seat Width | 40-48 cm |
| Seat Depth | 40-48 cm |
| Backrest Height | 40-50 cm |
To Next Page
