Handicare PUMA 40 Service Manual (English)

Other manuals for Handicare PUMA 40

Questions and Answers:

R
Ronald WeissAug 30, 2025
What does 'System Error' mean on my Handicare PUMA 40 Wheelchair and how can I fix it?
- E
  erica98Aug 30, 2025
  A 'System Error' indicates a fault that cannot be attributed to a specific module. Check all cables and connections. Cycle the power. If the error persists and the system contains 3rd party Modules: Disconnect all the none PGDT modules and cycle the power. If this has cleared the trip: Connect each 3rd party module in turn, cycling the power each time. If the trip reappears after one of the power cycles then the last module to have been added to the system must be defective. If the error persists, the PGDT control system may be defective.
O
othomasAug 25, 2025
Why ON/OFF light flashes 7 times on Handicare Mobility Aid?
- B
  Blake DavidsonAug 25, 2025
  If the ON/OFF light on your Handicare Mobility Aid flashes 7 times, it indicates a low battery voltage, or the batteries are flat or bad. Charge or replace the batteries. Note that if the voltage is low (less than 12V), the electronics won't work properly, and random LEDs of the DX controller may flash, preventing the wheelchair from functioning.
J
jonessarahSep 2, 2025
What does 'DIME Error' mean on my Handicare PUMA 40 Wheelchair and how can I fix it?
- T
  Timothy WallsSep 2, 2025
  A 'DIME Error' indicates an identification conflict between two modules in the system. If a new module has been introduced: Disconnect the new module and cycle the power. If no error is present, connect the new module to the system and cycle the power. If the error reappears, the new module is the cause. If there have been no additions: Disconnect one module at a time and cycle the power.
K
kwalkerSep 6, 2025
Why is the ON/OFF light flashing four times on my Handicare Scooter?
- G
  Gregory GonzalezSep 6, 2025
  If the ON/OFF light flashes four times on your Handicare Scooter, it could be due to a faulty connection or a defective m2 motor. Check the motor connections and cabling. If the connections are fine, the m2 motor may need to be replaced.
J
John LongAug 31, 2025
What does 'Left Lamp Short' mean on my Handicare PUMA 40 Wheelchair and what should I do?
- R
  robert36Sep 1, 2025
  A 'Left Lamp Short' means the control system has detected a short in either of the Lamp Circuits. Check the lamps, cables, and connections to the control system. If the error persists, the ISM may be defective.
T
Thomas EnglishAug 28, 2025
What causes an M1 Brake Error on my Handicare PUMA 40 Wheelchair?
- S
  Sonya WilliamsAug 28, 2025
  An M1 Brake Error indicates a problem in the solenoid brakes or their connections. Check the solenoid brakes, cables, and connections to the control system. If the error persists, the Power Module may be defective.
C
Carrie JohnsonSep 8, 2025
What does it mean if the ON/OFF light flashes once on my Handicare Scooter?
- R
  Robert PierceSep 8, 2025
  If the ON/OFF light flashes once on your Handicare Scooter, it indicates a DX module fault. Replace one or more modules. The 'on/off' LED indicates the condition of the entire system.
N
Nathaniel BrownSep 4, 2025
What to do if my Handicare Scooter ON/OFF light doesn't turn on and the wheelchair won't move?
- M
  Matthew ShortSep 4, 2025
  If the ON/OFF light doesn't illuminate and the Handicare Scooter remains stationary, consider these potential causes and solutions: * Ensure the controller plug is correctly inserted into the power module. It may be a stall timeout, place the joystick in neutral and try again. * Inspect the fuses and replace any that are defective. * Verify that the batteries are properly connected. * Check for loose battery connections and secure them.
A
Aaron PetersonAug 27, 2025
What does it mean when the service indicator flashes twice and the ON/OFF light flashes three times on a Handicare Wheelchair?
- D
  Daniel ParkerAug 27, 2025
  This indicates a battery fault or a defective M1 motor. Check the batteries and cabling, charge or replace the batteries, and check the motor connections and cabling. If the issue persists, the M1 motor may need to be replaced.
A
allisondavisSep 9, 2025
How do I fix a Joystick Calibration Error on my Handicare Scooter?
- M
  Matthew GibbsSep 9, 2025
  A Joystick Calibration Error on your Handicare Scooter means the joystick calibration process was unsuccessful. Enter OBP and attempt calibration. If the error persists, the Joystick Module may be defective.