Hansen QHPF1 - User Manual

HANSEN P4
Standardized gear units
Service manual
405 EFDN f
Standardized Réducteurs de Normzahnrad- Standaard
gear units vitesse standard getriebe tandwielkasten
Service Manuel Betriebs- Bedrijfs-
manual d'entretien anleitung handboek
SHIPPED
WITHOUT
OIL
LIVRE
SANS
HUILE
GELIEFERT
OHNE
ÖL
GELEVERD
ZONDER
OLIE
ISO 9001
Carefully
read this
manual
before
installing the
gear unit.
Lisez
attentivement
ce manuel
avant
d'installer le
réducteur.
Lesen Sie
diese
Betriebs-
anleitung vor
dem Einbau
des Getriebes
bitte sorg-
fältig durch.
Lees
zorgvuldig dit
bedrijfshand-
boek
vooraleer de
tandwielkast
te installeren.
Carefully read this manual
before installing the gear unit.
405 EFDN f
Standardized Réducteurs de Normzahnrad- Standaard
gear units vitesse standard getriebe tandwielkasten
Service Manuel Betriebs- Bedrijfs-
manual d'entretien anleitung handboek
SHIPPED
WITHOUT
OIL
LIVRE
SANS
HUILE
GELIEFERT
OHNE
ÖL
GELEVERD
ZONDER
OLIE
ISO 9001
Carefully
read this
manual
before
installing the
gear unit.
Lisez
attentivement
ce manuel
avant
d'installer le
réducteur.
Lesen Sie
diese
Betriebs-
anleitung vor
dem Einbau
des Getriebes
bitte sorg-
fältig durch.
Lees
zorgvuldig dit
bedrijfshand-
boek
vooraleer de
tandwielkast
te installeren.
405 EFDN f
Standardized Réducteurs de Normzahnrad- Standaard
gear units vitesse standard getriebe tandwielkasten
Service Manuel Betriebs- Bedrijfs-
manual d'entretien anleitung handboek
SHIPPED
WITHOUT
OIL
LIVRE
SANS
HUILE
GELIEFERT
OHNE
ÖL
GELEVERD
ZONDER
OLIE
ISO 9001
Carefully
read this
manual
before
installing the
gear unit.
Lisez
attentivement
ce manuel
avant
d'installer le
réducteur.
Lesen Sie
diese
Betriebs-
anleitung vor
dem Einbau
des Getriebes
bitte sorg-
fältig durch.
Lees
zorgvuldig dit
bedrijfshand-
boek
vooraleer de
tandwielkast
te installeren.
405 Ef

Summary

2. GENERAL

2.1.2. Security

Safety guidelines and precautions for working with the gear unit.

5. HANDLING

5.1. LIFTING EYE NUTS WITH BOLTS ATTACHED TO THE GEAR UNIT

Details on using lifting eye nuts and bolts for mounting.

6. INSTALLATION

6.4. ERECTION

6.4.1. Levelling

Procedures for correctly levelling the gear unit during installation.

6.4.2. Alignment

Instructions for accurately aligning the gear unit with machinery.

6.4.2.2. Connection motor - gear unit: allowable misalignment at the high speed shaft (including all shaft ends of single stage gear units)

6.5. SECURING OF SOLID SHAFT GEAR UNITS

6.5.1. Tightening torques for steel bolts grade 8.8

Torque specifications for securing solid shaft gear units with steel bolts.

6.5.2. Tightening torques for stainless steel bolts grade 80

6.6. SECURING OF HOLLOW SHAFT GEAR UNITS

6.6.1. Hollow shaft gear unit with shrink disc connection

Instructions for mounting hollow shaft units using a shrink disc.

6.6.2. Hollow shaft gear unit with keyway connection

6.7. LUBRICATION AFTER INSTALLATION

7. LUBRICATION

7.2. FORCED FEED LUBRICATION

7.2.1. Circulation lubrication

7.3. OIL SELECTION

7.4. OIL QUANTITY

7.5. THE FIRST OIL FILLING (see fig. 5)

7.6. GREASE SELECTION (see table page 38)

7.8. OIL DRAINING (see fig. 5)

10. BACKSTOPS

11. START UP

11.1. ALL GEAR UNITS

11.2. GEAR UNITS EQUIPPED WITH A BACKSTOP

12. MAINTENANCE

12.1. INSPECTION AND MAINTENANCE

12.2. OIL CHANGE AND REGREASING THE LUBRICATION POINTS

Steps for changing oil and regreasing lubrication points.

12.2.2. Oil change and regreasing

12.6. EXTENDED PERIODS OF STANDSTILL

12.8. REPAIRS

13. GREASE QUANTITIES FOR REGREASING

14. LUBRICANTS

14.1. MINERAL OILS AND GREASES

Table of recommended mineral oils and greases for gear units.

14.2. POLYALPHA-OLEFINE BASED SYNTHETIC OILS AND SUITABLE GREASE

Hansen QHPF1 Specifications

General

Brand	Hansen
Model	QHPF1
Category	DC Drives
Language	English