19
Before staring Installation Operation Specifications
No. 0 Description +100 +200 Description by channel
47 R/S_SAVE
Power outage recovery setting
EVSTOP.1 EVSTOP.2 Stop Running at event occurrence
48 PARA_INIT Parameter initialization HBC.1 HBC.2 Heater break current value
49 - - HBA.1 HBA.2 Heater break event current value
50 - - HB_HYS.1 HB_HYS.2 Heater break hysteresis
51
- -
PB.1
PB.2
Heating control Proportion control value
52
- - TI.1 TI.2
Heating control Integral control value
53 - - TD.1 TD.2
Heating control Differential control value
54 - - AP.1 AP.2
ALPH value
55 - - MR.1 MR.2 Manual reset
56 - - CT.1 CT.2 Heating control cycle
57 - - PO.1 PO.2 Heating control emergency output
58 - - HYS.1 HYS.2
ON/OFF heating control hysteresis
59 - - RO.1 RO.2
Heating control stop / output when monitor
60 - - RUP.1 RUP.2 SV increase temperature
61 EVSTS.1
Event status by channel
RDN.1 RDN.2 SV decrease temperature
62 EVSTS.2 RMIN.1 RMIN.2 SV change time (minute)
63 - - RHRS.1 RHRS.2 SV change time (hour)
64 - DR.1 DR.2 Control output
65 - - OHL.1 OHL.2 Output high limit
66 EV.1STS
Channel status by event
OLL.1 OLL.2 Auto tuning hysteresis
67 EV.2STS AT_HYS.1 AT_HYS.2 Auto tuning hysteresis
68 EV.3STS - - -
69 EV.4STS - - -
70 EV.5STS - - -
71 EV.6STS BS.1 BS.2 Input compensation
72 EV.7STS FL.1 FL.2 Input filter
73 EV.8STS SVH.1 SVH.2 SV High setting
74 - - SVL.1 SVL.2 SV low setting
75 - - FRH.1 FRH.2 Input high limit
76 EVBUS.1
Event bus output setting
FRL.1 FRL.2 Input low limit
77 EVBUS.2 SLH.1 SLH.2 High scale limit
78 EVBUS.3 SLL.1 SLL.2 Low scale limit
79 EVBUS.4 DOT.1 DOT.2 Set decimal point
80 EVBUS.5 - - -
81 EVBUS.6 PBC.1 PBC.2 Cooling control proportion value
82 EVBUS.7 TIC.1 TIC.2 Cooling control differential value
83 EVBUS.8 TDC.1 TDC.2 Cooling control differential value
84 - - CTC.1 CTC.2 Cooling control control cycle
85 - - POC.1 POC.2
Cooling control output at
emergency situation
86 PRS Communication protocol HYSC.1 HYSC.2 ON/OFF cooling control hysteresis
87 BPS Transmission speed ROC.1 ROC.2
Cooling control stop. Output at monitoring situation
88 PRI Parity bit -
89 STP Stop bit -
90 DLN Data length - - -
91 RPT Delay time HC.1 HC.2
Heating, heating/cooling control setting
92 - - HC_DB.1 HC_DB.2 Heating/cooling control deadband
93 - - -
94 - - - - -
95 ADDR Switch address - - -
96 MAX_CH Number of channels - - -
97 R_SYS System data - - -
98 R_OPT Option date - - -
99 ROMVER Version - -
-
To Next Page
Loading...
