HANYOUNG NUX ML-D2H - Page 24

Multi Loop Controller
22
Register address
(HEX)
Symbol
Description
Property
(R/W)
Setting range Unit
Initial
value
CH1 CH2
n : Number of
channel
97(61) R_SYS System data R - ABS -
98(62) R_OPT Option data R - ABS -
99(63) ROMVER Firmware version R - ABS -
101(65) 201(C9) PV Process value R EU (0 ~ 100%) ℃ -
102(66) 202(CA) SV Set vlalue R/W EU (0 ~ 100%) ℃ EU (0%)
103(67)
203(CB)
MV
Manipulated
Value
R 0.0 ~ 100.0
%
-
104
(68)
204
(CC)
CHSTS Channel R
All error status OR run
15 Bit: Set “1” at System Data error
14 Bit: Set “1” at Calibration Data error
13 Bit: Set “1” at input circuit error
12 Bit: Set “1” at EEPROM error
11 Bit: Set “1” after 24 hours of auto toning (AT)
10 Bit: Set “1” at RJC
9 Bit: Set “1” when exceeding ±5% input range
8 Bit: Set “1” at input sensor error (B. OUT)
2 Bit: Set “1” at auto tuning (AT) run
1 Bit: Set “1” at monitor mode
0 Bit: Set “1” at run start
ABS -
105
(69)
205
(CD)
EVSTS
Event channel
by channel 1~8
status
R
All events OR run
7 Bit(128): Set “1” at event channel 8 occurrence
6 Bit(64): Set “1” at event channel 7 occurrence
5 Bit(32): Set “1” at event channel 6 occurrence
4 Bit(16): Set “1” at event channel 5 occurrence
3 Bit(8): Set “1” at event channel 4 occurrence
2 Bit(4): Set “1” at event channel 3 occurrence
1 Bit(2): Set “1” at event channel 2 occurrence
0 Bit(1): Set “1” at event channel 1 occurrence
ABS -
106
(6A)
206
(CE)
OUTSTS Output status R
0: output (OFF)
1: output (ON)
ABS -
107
(6B)
207
(CF)
RJC
RJC temperature
value
R EU (0 ~ 100%) ℃ -
108
(6C)
208
(D0)
TC
Thermo couple
(TC) value
R EU (0 ~ 100%) ℃ -
109
(6D)
209
(D1)
INP Set input type R/W
0~18: Thermo Couple (TC)
20~23: Resistance Temperature Detector (RTD)
30~ 32: Direct Current Voltage (DCV)
* Refer to input type
ABS
1
(Thermo
couple
K Type)
110
(6E)
210
(D2)
CHMD
Set channel
mode
R/W
0: Stop mode
1: Monitor mode
2: Run mode
ABS 0
111
(6F)
211
(D3)
AT
Run PID auto
tuning(AT)
R/W
0: PID auto tuning (AT) stop
1: PID auto tuning (AT) start
ABS 0
112
(70)
212
(D4)
OUT Output type R
0 : OUT1 - RELAY, OUT2 - RELAY
1 : OUT1 - SSR/SCR, OUT2 - RELAY
2 : OUT1 - SSR/SCR, OUT2 - SSR/SCR
ABS
Follow
product
specs
113
(71)
213
(D5)
OUTS
SSR/SCR
output setting
R/W
'0' setting for SSR, '1' setting for SCR
1 Bit(2): SSR/SCR output setting for OUT2
0 Bit(1): SSR/SCR output setting for OUT1
ABS 0
114
(72)
214
(D6)
OUT_C_STS
Cooling control
output status
R
Output OFF
Output ON
ABS -