Harbor Freight Tools 95082 - User Manual

21 pages

Save Page as PDF

To Next Page

2-1/2 HP / 12” PLANER

95082

SET UP AND OPERATING INSTRUCTIONS

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

2010 by Harbor Freight Tools

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Revised 11h

Main Page

Questions and Answers

T
Tiffany HendricksSep 8, 2025
Why am I getting an uneven side-to-side depth of cut with my Harbor Freight Tools Planer?
- G
  Gregory JacksonSep 8, 2025
  An uneven side-to-side depth of cut with your Harbor Freight Tools Planer is likely due to the roller case not being level with the planer base. Adjust the roller case so that it is level.
T
Tina CalhounSep 10, 2025
Why is the fan on my Harbor Freight Tools 95082 so loud?
- M
  marksmithSep 10, 2025
  The fan on your Harbor Freight Tools Planer might be very loud because there is debris caught in the fan; remove the debris. Alternatively, the fan might be loose, so try tightening the hardware on the fan.
J
Justin CopelandSep 12, 2025
Why is the chain jumping on my Harbor Freight Tools Planer?
- L
  Lisa VasquezSep 12, 2025
  If the chain is jumping on your Harbor Freight Tools Planer, it could be due to worn sprockets, so have the sprockets replaced. It could also be a worn chain, in which case you should have the chain replaced.
M
Melissa SimmonsSep 13, 2025
What to do if board thickness does not match depth of cut scale on Harbor Freight Tools 95082?
- M
  michael98Sep 14, 2025
  If the board thickness does not match the depth of cut scale on your Harbor Freight Tools Planer, the indicator is likely not set correctly. Have the indicator repaired by a qualified technician.
P
Patrick FranklinSep 15, 2025
Why is the belt slipping on my Harbor Freight Tools 95082 Planer?
- A
  Alicia Mitchell DDSSep 16, 2025
  The belt slipping on your Harbor Freight Tools Planer is likely because the belt is loose. Replace the belt.
J
jhendersonSep 18, 2025
What to do if roller case will not lower on Harbor Freight Tools 95082 Planer?
- P
  perezashleeSep 18, 2025
  If the roller case will not lower on your Harbor Freight Tools Planer, it could be because the thickness gauge setting is restricting the roller case. Try resetting the thickness gauge.

Summary

Important Safety Information

General Power Tool Safety Warnings

Safety guidelines and precautions applicable to all power tools.

Instructions for Putting Into Use

Tool Set Up

Steps and warnings related to setting up the tool.

Work Piece and Work Area Set Up

Guidelines for preparing the material and the workspace.

Maintenance and Servicing

Cleaning, Maintenance, and Lubrication

Procedures for cleaning, general maintenance, and lubrication.

Carbon Brush Maintenance

Steps for inspecting and maintaining carbon brushes.

Blade Maintenance

Procedures for rotating or replacing planer blades.

Harbor Freight Tools 95082 Specifications

General

Knives	2
Maximum Depth of Cut	1/8 inch
Planing Width	12-1/2 inch
Voltage	120 V
Maximum Cutting Width	12-1/2 inch
Feed Rate	26 ft. per minute
Dust Port Size	2-1/2 inch