12
This menu is only available if the system has been setup for “pool and spa”. During the programmed
spa time, the Aqua Plus will turn on the filter pump and move the pool/spa valves into the “spa-only”
position. The heater will automatically heat the spa up to the programmed spa temperature (page 7).
This programmed spa operation will take precedence over all other automatic functions, only manual
operation of the filter button or pool/spa valve button will override this function.
If your pool has a separate jet pump or blower controlled by Aux1 and/or Aux2 , you will have to
program those separately.
This menu will appear only if the Lights are configured for timeclock. The lights will turn on and off at
the designated times. The only override on this function is manual on/off control by the “Lights”
button.
This menu will appear only if the Lights are configured for countdown timer. This setting is the time
after you manually turn on the lights until the Aqua Plus automatically turns off the lights. You can
also manually turn off the lights at an earlier time by pressing the LIGHTS button. If the Lights relay
is on during the programmed off time, it may be because of freeze protection.
Aux1 and Aux2 configurations are identical.
This menu will appear only if the Aux1 is configured for timeclock. The Aux output will turn on and off
at the designated times. If the Aux relay is off during the programmed on time— note that some pool
equipment (example pressure side pool cleaner) can only be operated when the filter pump is running
and the pool/spa valves are in the pool-only position—the Aqua Plus will keep the relay off until these
other conditions are suitable for operation. If the Aux relay is on during the programmed off time, it
may be because of freeze protection. Also, manual operation overrides the timeclock.
This menu will appear only if the Aux1 is configured for countdown timer. This setting is the time after
you manually turn on the Aux relay until the Aqua Plus automatically turns off the relay. You can also
manually turn off the relay at an earlier time by pressing the AUX1 button.
23
Maintenance Menu (only displays if Sensing System is enabled)
The Maintenance Menu will be displayed only if the optional AQL-CHEM is used and the Sensing System is
enabled in the Chemistry Config. Wizard. This menu is used to perform functions relating to the AQL-CHEM ORP
and pH sensing kit.
pH Calibration
Wizard, + to enter
Push to access pH Calibration Wizard
Move to previous/next menu item
Use this Wizard to calibrate the AQL-CHEM’s pH probe. This requires a manual pH test of the pool
water using a dependable red phenol test kit.
Clean Probe Wizard
+ to enter
Push to access Clean Probe Wizard
Move to previous/next menu item
Use this Wizard to clean the AQL-CHEM’s ORP and pH probes. The probes must be clean and free
from oil, chemical deposits and contamination to function properly. Slow response, increased need to
calibrate, and inconsistent readings are indications that the probes need to be cleaned.
Set Day and Time
Wednesday 10:37P
Adjust time setting
Move between start and stop times & to previous/next menu item
Spa-all
6:00P to 9:00P
Spa-wkend
6:00P to 9:00P
Spa-wkday
6:00P to 9:00P
Adjust time setting
Adjust time setting
Move between start and stop times & to previous/next menu item
Move between start and stop times & to previous/next menu item
Set Day and Time
Wednesday 10:37P
Adjust time setting
Move between start and stop times & to previous/next menu item
Lights-all
8:00P to 11:00P
Lights-wkend
8:00P to 11:00P
Lights-wkday
8:00P to 11:00P
Adjust time setting
Adjust time setting
Move between start and stop times & to previous/next menu item
Move between start and stop times & to previous/next menu item
or
or
Lights-CountDn
0:20
Adjust time setting (Manual On/Off, 0:05, 0:10, 0:015...)
Move to previous/next menu item
Set Day and Time
Wednesday 10:37P
Adjust time setting
Move between start and stop times & to previous/next menu item
Aux1-all
8:30A to 4:00P
Aux1-wkend
8:30A to 4:00P
Aux1-wkday
8:30A to 4:00P
Adjust time setting
Adjust time setting
Move between start and stop times & to previous/next menu item
Move between start and stop times & to previous/next menu item
Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15...)
Move to previous/next menu item
To Next Page
Loading...
Need help?
General
