Hayward Micro Star-Clear

To Next Page

IS2001540LS-99

OWNER’S GUIDE

Your Micro Star-Clear cartridge filter has an output rating of 1400 gallons (5299 L) per hour.

The filter and pump are combined on a molded mounting base and are manufactured from

durable, corrosion-proof materials. The system is designed for installation below the pool

water line.

The Micro Star-Clear filter system utilizes a reusable single element, reinforced polyester

filter cartridge to provide a high degree of water clarity with absolute minimum care.

Removal of the cartridge for routine cleaning is fast and easy to do.

The SP1540 series Power-Flo LX pump is a non-corrosive centrifugal pump with pressure,

flow and operation designed for swimming pool service and may be operated on an inter-

mittent or continuous basis.

SYSTEM LOCATION

Though the system is designed for outdoor use, it is

advisable to protect electrical components from the

weather. Select a well-drained area, one that will not

flood when it rains.

Position the system below the swimming pool water

line and as close to the pool as possible. Set the

mounting platform level. Allow a minimum clearance

for cartridge removal. Be sure the pipe connections,

drain, etc., are accessible for convenient operation

and cartridge removal.

TO ASSEMBLE THE SYSTEM

Place pump and motor on mounting base. Align holes

in motor base with holes in mounting base and secure

with two screws and washers provided.

Securely thread sweep elbow, with 3-4 wraps of

Teflon pipe tape, into outlet of pump. Position so that

large thread end points back toward the motor, at an

angle, toward corner of base.

Thread the ball end of union, with union nut, into

filter connection marked “IN.” Use Teflon tape (3-4

wraps on thread) and screw in as far as possible hand

tight, then one additional turn with a wrench.

Adjust ball and socket and join by hand tightening

union nut. Do not overtighten.

All plumbing connections on the system are 1-1/2”

N.P.T. When making connections, use plastic male-

end adapters and flexible hose. Apply three turns of

Teflon tape or plastic pipe sealant to the male

threads. Screw the fitting into the thread hand tight;

then using a wrench, tighten one more full turn.

Additional tightening is unnecessary and could

result in damage to components.

NOTE: For extra convenience, you may wish to install

valves on the inlet and discharge of the system to

prevent back flow of water when removing cartridge.

See dealer for further information.

Connect the pool suction plumbing between the

skimmer pool outlet, and the pump. Connect the pool

return (inlet) plumbing.

A drain plug is furnished with each filter and is all

that is needed for complete filter draining. A manual

air vent valve is furnished to aid in bleeding off

unwanted air when starting the filter.

All electrical connections must be made in

accordance with local codes.

Check for joint leaks before operating the system.

Refer to pump instruction booklet for pump

information.

BEFORE STARTING THE FILTER

Superchlorinate the pool water by adding unstabilized

granular or liquid chlorine. Stabilized forms of chlorine

are recommended for normal daily use after the initial

clean up of the water. Follow chemical manufacturer’s

recommendations for superchlorination and daily use.

STARTING THE FILTER

Open manual air vent valve a few turns. CAUTION: All

suction and discharge valves must be open when

starting the system. Failure to do so could cause

severe personal injury and/or property damage.

Prime and start the pump following the manufacturer’s

instructions. Air trapped in the system will automatically

vent to the pool and out vent valve. Close vent valve as

soon as air is vented.

10.

MODEL C2001540LS SERIES

Need help?

Do you have a question about the Hayward Micro Star-Clear and is the answer not in the manual?

Summary

System Location and Assembly

System Location

Choose a well-drained area protected from weather, positioned below pool water line.

Assemble the System

Instructions for mounting pump, connecting plumbing, and ensuring all connections are secure.

Before Starting the Filter

Procedure for superchlorinating pool water before initial filter start-up.

Starting the Filter

Steps for safely starting the filter system, including opening air vents and priming the pump.

Filtering and Cartridge Maintenance

Filtering Process

Explanation of how filtration works and when to clean or replace the cartridge.

Removing Cartridge Element

Detailed steps for shutting off the pump and safely removing the filter cartridge.

Parts Diagram

Illustrative diagram of the filter system components with a part list.

Cartridge Care and Pool Chemistry

Reinstalling Cartridge Element

Steps for properly reinstalling the cleaned or new filter cartridge.

Cleaning Cartridge

Methods for cleaning the filter cartridge using pressure washing or chemical soaking.

Algae Control

Guidance on preventing and treating algae growth with proper chlorine levels.

Vacuuming Pool

Instructions on how to vacuum the pool directly into the filter.

Winterizing

Procedure for preparing the filter system for winter to prevent damage.

Service and Repairs

Information on contacting authorized dealers for service and repairs.

Pool Chemistry Guidelines

Table of suggested pool chemistry levels and actions to adjust them.