Why is my Hayward Swimming Pool Vacuum not moving forward?
The Hayward Swimming Pool Vacuum might not be moving forward due to low or no water pressure. To solve this, inspect the filtration and booster pumps, valves, and cleaner connections. Also, verify the cleaner pressure and backwash if necessary.
What to do if my Hayward Swimming Pool Vacuum has little or no sweep hose movement?
If your Hayward Swimming Pool Vacuum has little or no sweep hose movement, it could be due to several reasons: * The sweep hose power might be too weak; increase the hose power. * There might be a hole in the sweep hose; replace it. * Debris might be clogging the sweep hose; disconnect the sweep hose and flush it out.
What to do if my Hayward Swimming Pool Vacuum hose frequently tangles?
If the hose on your Hayward Swimming Pool Vacuum is frequently tangling, there might be several reasons: * The float might not be properly placed; check its position on the hose. * The hose might be too long; check the hose length. * The sweep hose might not be moving; check it for holes or clogs and increase its power.
Why is my Hayward TriVac 500 Swimming Pool Vacuum's sweep hose spraying out of the pool?
If the sweep hose on your Hayward Swimming Pool Vacuum is spraying out of the pool, it's likely that the sweep hose power is too strong. You should reduce the sweep hose power to correct this.
What to do if my Hayward TriVac 500 runs in small circles?
If your Hayward Swimming Pool Vacuum runs in small circles, the hose assembly might be bent. Lay it out in the sun until it straightens out.
Why Hayward Trivac Swimming Pool Vacuum running on side or upside down?
If your Hayward Trivac Swimming Pool Vacuum is running on its side or upside down, it could be due to heavy debris in the bag; empty the bag. It may also be due to an incorrect pressure setting; check the operating pressure.
Why Hayward TriVac 500 Swimming Pool Vacuum cannot climb to the surface in TOP mode?
If your Hayward Swimming Pool Vacuum cannot climb to the surface in TOP mode, it may be due to an incorrect pressure setting; check the operating pressure. Another reason could be too much heavy debris in the bag, so empty the bag.
What to do if Hayward TriVac 500 Swimming Pool Vacuum gets stuck on shallow area of pools?
If your Hayward Swimming Pool Vacuum gets stuck on shallow areas of pools, like beach entries or tanning shelves, the sweep hose may be interfering with the obstacle. Try operating the cleaner without the sweep hose.
What to do if Hayward TriVac 500 does not cover the entire pool?
If your Hayward Swimming Pool Vacuum does not cover the entire pool, the sweep hose may be affecting the cleaning pattern of the cleaner. Try operating the cleaner without the sweep hose.
What to do if Hayward TriVac 500 cannot recover from obstacle?
If your Hayward Swimming Pool Vacuum has an inability to recover from obstacles or specific areas, the sweep hose may be interfering with the obstacle. Try operating the cleaner without the sweep hose. Additionally, the operating pressure may be too low, so check the operating pressure.
Do not use the cleaner to remove large debris in new pools.
Remove the cleaner from the pool before chemically shocking it.
Do not swim in the pool while the cleaner is operating.
Store the cleaner in a shaded, safe area with hoses stored straight.
Keep the cleaner and its components away from children and pets.
Remove the cleaner when performing a pool backwash.
Manually remove large debris before cleaner operation, especially after storms.
Perform a backwash and clean filter, skimmer, and pump baskets.
Maintain specific pH, Chlorine, and Total Alkalinity levels for operation.
Instructions for connecting to a dedicated return line with specific fittings.
Instructions on installing the universal wall fitting, using Teflon tape for plastic threads.
Measure hose length to the farthest point, add 3-4 feet, and cut excess, adjusting floats accordingly.
Ensure the debris bag is properly attached and not pinched during installation.
Learn how to detach the debris bag by pulling the frame back and up.
Tips for cleaning the debris bag, noting that drying makes debris removal easier.
Use a flat blade screwdriver to set the wall quick connect to 23 PSI (+/- 3).
Describes pool coverage and normal cleaning cycle duration, noting minimum water depth.
Instructions for switching between Bottom to Skim and Skim to Bottom modes.
Adjust sweep hose power by turning the knob counter-clockwise for slow movement, clockwise for excessive spraying.
Procedure for safely disconnecting and removing the cleaner from the pool.
Instructions for cleaning the in-line filter, checking the o-ring, and noting potential plumbing issues.
Instructions for replacing the sweep hose, including part number.
Guidance on replacing sweep hose rollers when worn to the outer groove, with part number.
Information on when and how to replace the debris bag, including part numbers.
Procedure for replacing swivels if they cease to turn or leak, with part number.
Instructions for replacing tires when wear marks appear, including part number and quantity.
Guidance on replacing side rollers when they wear down, with part number and quantity.
Details the limited warranty period for TriVac 500 (1 year) and TriVac 700 (2 years) against defects.
General| Cable Length | 60 ft |
|---|---|
| Type | Robotic |
| Filter Type | Debris Canister |
| Cleaning Area | Up to 20 x 40 ft |
| Suitable for Pool Types | In-ground pools |
| Cleaning Pattern | Random |
| Warranty | 2 years |
To Next Page