Healthrider HRTL77105 User Manual

30 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

USER'S MANUAL

Visit our website at

www.healthrider.com

new products, prizes,

fitness tips, and much more!

V

Serial

Number

Decal

Model No. HRTL77105.0

Serial No.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if parts are

damaged or missing, PLEASE

CONTACT OUR CUSTOMER

SERVICE DEPARTMENT

DIRECTLY.

CALL TOLL-FREE:

1-888-922-4222

Mon.–Fri., 6 a.m.–6 p.m. MST

ON THE WEB:

www.healthriderservice.com

Table of Contents

Questions and Answers:

N
Nicole MacdonaldAug 9, 2025
What to do if the walking belt is off-center or slips on Healthrider HRTL77105?
- S
  Steven RobertsonAug 9, 2025
  To recenter the walking belt on your Healthrider Treadmill, first remove the key and unplug the power cord. If the belt has shifted left, turn the left rear roller bolt clockwise 1/2 turn. If it has shifted right, turn the bolt counterclockwise 1/2 turn. Avoid overtightening. Plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat as needed. If the walking belt slips, remove the key and unplug the power cord. Turn both rear roller bolts clockwise 1/4 turn. Ensure you can lift each edge of the belt 3 to 4 inches off the platform. Plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until properly tightened.
E
ericgrantAug 12, 2025
How to turn on Healthrider HRTL77105 Treadmill?
- V
  victoria79Aug 12, 2025
  If your Healthrider Treadmill's power doesn't turn on, ensure the power cord is plugged into a surge suppressor, which is then plugged into a grounded outlet. Use a single-outlet surge suppressor meeting the specified requirements. Note that the treadmill isn't compatible with GFCI-equipped outlets. Also, make sure the key is inserted into the console after plugging in the power cord. Finally, check the circuit breaker near the power cord; if the switch protrudes, wait five minutes, then press it back in to reset.
B
Brenda McintoshAug 16, 2025
How to recalibrate incline on Healthrider HRTL77105 Treadmill?
- E
  Elizabeth EdwardsAug 17, 2025
  To recalibrate the incline on your Healthrider Treadmill, insert the key into the console and press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, reinsert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level.
T
Tony BakerAug 21, 2025
Why does my Healthrider HRTL77105 power turn off during use?
- J
  Jackson SolisAug 21, 2025
  If your Healthrider Treadmill's power turns off during use, first check the circuit breaker located on the frame near the power cord. If tripped, wait five minutes, then press the switch back in. Also, ensure the power cord is securely plugged in; if so, unplug it, wait five minutes, then plug it back in. Finally, remove and reinsert the key fully into the console. If the treadmill still won't run, further assistance may be needed.
Z
Zachary WrightAug 26, 2025
How to fix walking belt slowing down on Healthrider HRTL77105 Treadmill?
- T
  Tina AlexanderAug 26, 2025
  If the walking belt slows down when you walk on your Healthrider Treadmill, ensure you're using a single-outlet surge suppressor that meets the specifications. If the walking belt is overtightened, remove the key and unplug the power cord. Use an Allen wrench to turn both rear roller bolts counterclockwise 1/4 turn. The belt should allow you to lift each edge 3 to 4 inches off the platform. Plug the cord back in, insert the key, and run the treadmill for a few minutes. Repeat until the belt is properly tightened.
A
Alex SmithAug 30, 2025
What to do if chest pulse sensor doesn't work on Healthrider HRTL77105 Treadmill?
- R
  richard49Aug 30, 2025
  If the chest pulse sensor on your Healthrider Treadmill isn't working, consult the section on 'CHEST PULSE SENSOR TROUBLE'. If it still malfunctions, replace the battery. Locate the battery cover on the back of the sensor, use a coin to turn the cover counterclockwise to the 'open' position, and remove the cover. Remove the old battery and insert a new CR 2032 battery with the writing on top, ensuring the rubber gasket is in place. Replace the cover and turn it to the closed position.
R
Robert KellySep 3, 2025
How to fix speed display on Healthrider Treadmill?
- E
  Edward GuzmanSep 3, 2025
  To fix the speed display on your Healthrider Treadmill console, remove the key and unplug the power cord. Carefully tip the treadmill down. Remove the 1” and 2” screws from the hood. Raise the uprights and carefully remove the hood. Locate the Reed Switch and the Magnet on the left side of the Pulley. Turn the Pulley until the Magnet is aligned with the Reed Switch, ensuring they are about 1/8” apart. If needed, loosen the Screw, move the Reed Switch slightly, and retighten it. Reattach the hood, and run the treadmill for a few minutes to check the speed reading.

Healthrider HRTL77105 Specifications

General

Incline	0-12%
Weight Capacity	300 lbs
Display	LCD
Programs	12
Heart Rate Monitoring	Yes

Related product manuals

PRO H500i HRTL71706.0

Healthrider HRTL10911

Preview: Healthrider HRTL14912

Healthrider HRTL14912

Preview: Healthrider HRTL16940

Healthrider HRTL16940

Preview: Healthrider HRTL14900

Healthrider HRTL14900

Preview: Healthrider HRTL34305.0

Healthrider HRTL34305.0

Healthrider S900i HRTL19990

Preview: Healthrider S700i HRTL16990

Healthrider S700i HRTL16990

Healthrider H110i HRTL34306.0

Healthrider Outlook HRTL89406.0

Healthrider Outlook HRTL89406.2

Preview: Softstrider HRTL59215.0

Softstrider HRTL59215.0