HEARBUDS &
HEARBUD HEADSET
MONITOR
Hearbuds
TM
provide an
affordable in-ear monitor
headset that delivers
professional performance
at a great value. By
creating acoustic chambers at the ear, hearbuds not only
dramatically improve the sound of standard in-ear
headphones and ear-pieces, their molded, 100% silicon,
design also significantly reduces unwanted background
noise levels - enabling you to enjoy sound clarity at lower
volumes. Included in each package are three sizes for a
perfect fit. And, because they're audiologically designed,
they're comfortable to wear and won't fall out of your
ears, either!
Features:
• Better sound quality at lower volumes
• Can be used on stage and in the studio
• Great for Hear Back, MP3 players, cell-phones, and
other personal audio
• Hearbuds alone fit most in-ear headsets
• Works great in noisy environments because they
block unwanted sounds
• Comfortable, safe, and secure
• Designed by audiologists
• Washable
HEAR BACK SYSTEM ACCESSORIES
EXTREME EXTENDER ADAT IN/OUT
ADAT Extreme Extenders
TM
IN/OUT are available for
converting from ADAT optical to HearBus and vice versa.
Extender Features:
• Extend ADAT® Optical cables up to 500 feet
• Convert HearBus to ADAT® Optical or vice versa
• Uses standard CAT5E cables
• Does not affect sound quality
• Small size, durable construction
• Clock Status LED on Extreme Extender OUT
The units were designed to solve ADAT optical distance
limitations. The extreme extender ADAT IN converts ADAT
optical to HearBus.
Using CAT5E the effective length of an ADAT optical
interface can be extended up to 500 feet. This is
accomplished without any loss of audio quality. The ADAT
"Thru" output provides a buffered pass-thru for connection
to local ADAT devices.
The Extreme Extender ADAT OUT converts the CAT5E
HearBus to ADAT optical. Two parallel optical outputs on
the Extender ADAT OUT provide drive for two separate
ADAT devices. A bi-color clock status LED indicates the
presence (green) or absence (red) of the ADAT clock.
In addition to acting as an ADAT optical extender, the
Extreme Extender ADAT IN may be connected to the
optical output of any ADAT device, such as a DAW, mixer,
etc. and connected to the input of a Hear Back hub.
The extreme extender ADAT OUT can be connected to the
HearBus out of a hub to obtain two ADAT outputs.
CABLES - Quality cables that work with your Hear Back
System.
ADAT OUT
ADAT IN
ADAT OUT
ADAT THRU
HearBus Out
HearBus IN
9VDC
CLK
PWR
CAT5E cables are
available in 2, 12,
25, 50, and 100
foot lengths.
Optical cables
are available in 6,
12, and 25 foot
lengths.
EXTREME EXTENDER
ADAT IN
Connections:
EXTREME EXTENDER
ADAT OUT
ADAT® is a registered trademark of Alesis Corporation.
HEAR BACK SYSTEM DESCRIPTION
The basic Hear Back™ system consists of a hub
and personal mixers. The hub receives any of
the three input signals and converts them to
HearBus digital audio plus power. The mixers
are connected to the hub using CAT5E cable.
A single hub supplies digital audio and power to
a maximum of eight mixers. That's one for you
and everybody in the band! If that's not enough,
the hubs can be daisy-chained using the
HearBus In and HearBus Out for virtually
unlimited system size.
The hub may be connected to recording
equipment, digital audio workstations, and
analog or digital consoles.
The mixer is placed near the talent and gives
them control over the audio inputs. The user-
friendly system saves system setup time.
• Virtually unlimited system size
• Excellent quality and audio fidelity
• High power - low distortion
headphone amplifiers
• Very long interconnect without loss
of audio quality
• Three audio inputs: ADAT® optical,
analog, and HearBus are switch
selectable from the front panel
• Local control of up to ten channels
of audio - 8 inputs plus a stereo Aux
input
• Built-In DSP limiter for hearing and
monitoring device protection
• Headphone amplifier fault LED
• Bus status indicator
• Link indicators/switches - links mono
pairs for stereo operation
•
Standard CAT5E cable for power
and signal connection to mixers
• Built-in cable strain relief
• Balanced line outputs - mono/stereo
• Stereo AUX in
• Built-In mic stand mount as well as
desktop mount capability
ADVANTAGES / FEATURES
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Statement
0318
To Next Page
Loading...