Heat & Glo CURVE 100 User Manual (English)

Questions and Answers:

P
Paul SerranoAug 17, 2025
Why is smoke escaping from my Heat & Glo Wood stove?
- F
  fwellsAug 18, 2025
  Smoke might escape from your Heat & Glo Wood stove due to several reasons. It could be due to damp wood, so ensure the wood is dry. The chimney might not be drawing properly, or its dimensions may be incorrect for the stove, so check the chimney draw and dimensions. Blockages in the smoke gas pipe or chimney can also cause this, so clear any blockages. Verify the chimney height and ensure the flue pipe isn't obstructing. A vacuum in the room can also cause smoke to escape, so adjust room ventilation. Also, ensure you wait until the embers are burned down before opening the door and improve chimney draw if it is not drawing sufficiently.
S
Sharon AdamsAug 20, 2025
Why is wood burning too quickly in my Heat & Glo Wood stove?
- A
  adamsalexisAug 20, 2025
  If wood is burning too quickly in your Heat & Glo Wood stove, it might be because the air valves are set incorrectly; adjust them accordingly. Also, check if the baffle plates are incorrectly mounted or missing, and correct their placement. Using inferior firewood like waste wood or pallets can also cause this issue, so use high-quality firewood. Finally, ensure the chimney size is correct, as a chimney that is too large can cause rapid burning.
S
Shelby ThompsonAug 22, 2025
How to prevent excessive soot build-up in my Heat & Glo Wood stove chimney?
- T
  Tara JonesAug 22, 2025
  Excessive soot build-up in your Heat & Glo Wood stove chimney may be due to poor burning, indicating that more air is required; increase the air supply. Damp wood can also contribute to this issue, so ensure the wood you are using is dry.
M
Mr. Erik AllenAug 25, 2025
Why is my Heat & Glo CURVE 100 not heating well?
- R
  Randy RodriguezAug 26, 2025
  If your Heat & Glo Wood stove isn't heating well, it could be due to damp wood; ensure the wood is dry. Insufficient wood can also cause poor heating, so add more wood. The wood quality might be inferior with a low fuel value, so use higher quality wood. Also, ensure the baffle plates are correctly fitted.
J
jimmycunninghamAug 30, 2025
Why is the surface of my Heat & Glo Wood stove turning grey?
- A
  Alexandra WaltersAug 30, 2025
  If the surface of your Heat & Glo Wood stove is turning grey, it indicates overheating. Please refer to the heating instructions for proper operation.
D
Dean QuinnSep 1, 2025
Why is there excessive soot build-up in my Heat & Glo Wood stove chimney?
- M
  Michelle PeckSep 1, 2025
  Excessive soot build-up in your Heat & Glo Wood stove chimney can occur due to poor burning, meaning more air is required; increase the air supply. Also, using damp wood can cause this issue, so ensure you use dry wood.
M
Mr. Joseph MurphySep 4, 2025
What to do if my Heat & Glo CURVE 100 Wood stove has poor heating performance?
- N
  nguyenrobinSep 4, 2025
  If your Heat & Glo Wood stove has poor heating performance, it could be due to several factors. Try using dry wood, as damp wood reduces heating efficiency. Make sure you are using enough wood and that it is of higher quality. Also, check that the baffle plates are fitted correctly.
K
Kim JonesSep 6, 2025
How to prevent soot build-up on the glass of my Heat & Glo CURVE 100 Wood stove?
- L
  Lisa HernandezSep 7, 2025
  To prevent soot build-up on the glass of your Heat & Glo Wood stove, adjust the secondary airflow setting. Reduce primary air. Use dry wood. Use smaller pieces of wood when lighting the stove and use better quality firewood.
A
Autumn NguyenSep 9, 2025
What causes my Heat & Glo CURVE 100 to burn wood too quickly?
- N
  Nancy RobinsonSep 9, 2025
  Your Heat & Glo Wood stove might be burning wood too quickly if the air valves are set incorrectly; adjust them. Ensure baffle plates are correctly mounted. Using better quality firewood is also important. The chimney size should also be appropriate.
B
Beth KlineSep 12, 2025
What should I do if my Heat & Glo Wood stove smells?
- D
  Dr. Stephanie ReyesSep 12, 2025
  To address the odour coming from your Heat & Glo Wood stove, open a window or a door for ventilation. Ensure the stove is heated up sufficiently to avoid odours later.