How to fix E07 error on HemoCue Measuring Instruments?
The E07 error on your HemoCue Measuring Instruments indicates low battery power. To resolve this: 1. Replace the batteries. Turn off the analyzer and replace the batteries with 4 type AA batteries. 2. Alternatively, use the power adapter.
What to do if HemoCue Measuring Instruments show an error code?
If your HemoCue Measuring Instruments are displaying an error code, try turning the analyzer off and then on again after waiting for 30 seconds. If that doesn't work, use a new microcuvette and repeat the measurement. If the error persists, consult the specific error code details.
How to fix HemoCue Hb 301 Medical Equipment E41-49 error?
If the HemoCue Medical Equipment displays E41-49, it could be due to: * A scratched optronic unit from incorrect maintenance. Clean the optronic unit as described in the maintenance section using the HemoCue Cleaner. The analyzer needs service; contact your distributor. * A hardware error. The analyzer needs service; contact your distributor.
How do I fix HemoCue Hb 301 E10-E30 error codes?
If the HemoCue Medical Equipment displays E10–E30, it indicates a dirty optronic unit, faulty electronics, or a faulty optronic unit. Turn off the analyzer and clean the optronic unit as described in the maintenance section. If the problem continues, the analyzer needs service; contact your distributor.
What does error E08 mean on HemoCue Hb 301?
If the HemoCue Medical Equipment displays E08, it indicates a light-blocking item in the cuvette holder. Ensure that the analyzer and microcuvettes are used according to the operating manual and instructions for use. If the problem persists, the analyzer needs service; contact your distributor.
What does E06 error mean on HemoCue Medical Equipment analyzer?
If the HemoCue Medical Equipment displays E06, it indicates an unstable blank value, possibly because the analyzer is cold. Turn off the analyzer and allow it to reach room temperature. If the problem continues, the analyzer needs service; contact your distributor.
How to troubleshoot HemoCue Medical Equipment E01-E05 errors?
If the HemoCue Medical Equipment displays E01–E05, it indicates a dirty optronic unit, faulty electronics, or a faulty optronic unit. To resolve this, turn off the analyzer and clean the optronic unit as described in the maintenance section. If the problem persists, the analyzer needs service; contact your distributor.
What does E40 error mean on HemoCue Hb 301?
If the HemoCue Medical Equipment displays E40, it may be due to: 1. Improper replacement of the cuvette holder after cleaning. Ensure it is correctly replaced as described in the maintenance section. 2. A dirty optronic unit. Clean it as described in the maintenance section. 3. Using a non-HemoCue Hb 301 Microcuvette. Only use HemoCue Hb 301 Microcuvettes. 4. A damaged microcuvette. Use a new microcuvette and repeat the measurement.
What causes E00 error on HemoCue Hb 301?
If the HemoCue Medical Equipment displays E00, it could be due to: * A faulty cuvette. Check the expiration date of the microcuvettes and try a new one. * A circuit board issue. In this case, the analyzer requires service, so contact your distributor.
What to do if HemoCue Hb 301 analyzer shows an error code?
If the HemoCue Medical Equipment displays an error code, first turn off the analyzer, wait 30 seconds, and then turn it back on. Use a new microcuvette and repeat the measurement. If the problem persists, consult the specific error code details.
General| Sample Volume | 10 µL |
|---|---|
| Sample Material | Capillary, venous or arterial whole blood |
| Wavelengths | 506 nm and 880 nm |
| Calibration | Factory calibrated |
| Precision | CV ≤ 1.5% |
| Measurement Principle | Photometry |
| Measurement Range | 0-25.6 g/dL |
| Analysis Time | Within 1 minute |
| Operating Temperature | 15-30°C (59-86°F) |
| Power Supply | AC adapter or 4 x AA batteries |
| Weight | 350 g (including batteries) |
| Battery Life | Approximately 1, 000 tests |
| Dimensions | 85 x 160 x 43 mm |
| Accuracy | Within ±1.5% or ±0.3 g/dL, whichever is greater |
Lists and illustrates all parts included with the HemoCue Hb 301 Analyzer.
Steps to set up, power on, and confirm analyzer readiness for use.
Detailed procedure for collecting and measuring capillary blood samples.
Procedure for performing tests with control materials for quality assurance.
How to connect the analyzer for data transfer or printing results.
Instructions for cleaning the cuvette holder and optronic unit.
Solutions for common analyzer errors and symptoms.
Details on dimensions, weight, operating conditions, accuracy, and certifications.
Guidance on EMC requirements and recommendations for safe operation.
Information on product warranty, service, and environmental disposal.
To Next Page
