What does error code “E-18-A” “E-18-B” “E-18-C” mean on Henny Penny Fryer?
If the Henny Penny Fryer displays “E-18-A”, “E-18-B”, or “E-18-C”, turn the switch to the OFF position, then back to ON. If the display still indicates a failed sensor, have the connectors checked at the control board and have the sensor checked and replaced if necessary.
What to do if oil will not drain from vat in my Henny Penny Fryer?
If the Henny Penny Fryer oil will not drain from the vat, it is likely because the drain valve is clogged with crumbs or the drain trough is clogged. To fix this, open the valve and force a cleaning brush through the drain. Also, remove the right side panel, remove the plug from the end of the trough, and clean the trough.
What does error code “E-6B” mean on Henny Penny Fryer?
If the Henny Penny Fryer displays “E-6B”, it indicates the temperature probe is shorted. Turn the switch to the OFF position, then turn it back to ON. If the display continues to show “E-6B”, the temperature probe should be checked.
What does error code “E-6A” mean on Henny Penny Fryer?
If the Henny Penny Fryer displays “E-6A”, it indicates the temperature probe is open. Turn the switch to the OFF position, then back to ON. If the display continues to show “E-6A”, the temperature probe should be checked.
What does error code “E-5” mean on Henny Penny Fryer?
If the Henny Penny Fryer displays “E-5”, it means the oil is overheating. Turn the switch to the OFF position, then back to ON. If the display continues to show “E-5”, the heating circuits and temperature probes should be checked.
What does error code “E-4” mean on Henny Penny Fryer?
If the Henny Penny Fryer displays “E-4”, it indicates the control board is overheating. Turn the switch to the OFF position, then back to ON. If the display continues to show “E-4”, check the louvers on each side of the unit for obstructions.
How to resolve control error code “E-31” on Henny Penny Fryer?
If the Henny Penny Fryer displays control error code “E-31”, it means the elements are up. Lower the elements completely into the vat to resolve this.
Why does my Henny Penny Fryer filter motor runs but pumps oil slowly?
If the Henny Penny Fryer filter motor runs but pumps oil slowly, check the following: * Ensure all filter line connections are tight. * Change the filter paper or pad if it's clogged. * Refer to the assembly instructions on the inside of the door to ensure the filter is reassembled correctly.
What to do if the vat is under-filled in my Henny Penny Fryer?
If the Henny Penny Fryer vat is under-filled, it could be due to a few reasons: * The JIB might be low or empty; fill the JIB. * The JIB oil line could be clogged or collapsed; check the JIB line, tube, and connection. * The filter pan might need cleaning; clean the filter pan and change the paper or pad.
Why won't my Henny Penny Fryer filter motor run?
If your Henny Penny Fryer filter motor will not run, here are a few things you can check: * Make sure the power cord for vat #1 is plugged in. * Check the circuit breakers behind the left door (beside the control circuit breakers) and reset them if needed. * The thermal reset button on the rear of the pump motor might be tripped. Allow time for the motor to cool, then press hard against the button with a screwdriver until it clicks.
General| Model | EEE-141 |
|---|---|
| Product Name | Evolution Elite |
| Frypot Width | 14 inches |
| Frypot Depth | 14 inches |
| Number of Fry Pots | 1 |
| Type | Open Fryer |
| Oil Capacity | 50 lbs |
| Electrical | 208V/240V |
| Phase | 3 |
| Controls | Digital |
| Temperature Range | 200°F |
| Oil Filtration | Automatic |
To Next Page
