Hercules HD035B - User Manual

Questions and Answers

J
Jay FordAug 18, 2025
Why Hercules HD035B Sander does not sand effectively?
- C
  cdavisAug 18, 2025
  If your Hercules Sander isn't sanding effectively: * The disc accessory might be loose on the spindle. Ensure the disc accessory arbor is correct and the outer flange/arbor nut is tight. * The disc accessory may be damaged, worn, or the wrong type for the material. Check the condition and type of disc accessory, and use only the proper type in good condition. * Product sprays off polishing pad. Reduce RPM to minimum setting.
C
Christian BlackAug 20, 2025
How to fix a Hercules HD035B that won't start?
- M
  Mark ChambersAug 20, 2025
  If your Hercules Sander isn't starting, there are several potential causes: * The battery pack may not be properly connected. Remove the battery pack, ensure there are no obstructions, reinsert it correctly, and press firmly until it locks. * The battery pack might not be charged. Ensure the charger is connected and working, and allow sufficient time for the battery to recharge. * The battery pack could be burnt out. Dispose of the old battery pack properly and replace it. * There may be internal damage or wear. In this case, have a technician service the tool.
D
Desiree MasonAug 22, 2025
Why is my Hercules HD035B Sander overheating?
- D
  Dorothy BaileyAug 23, 2025
  If your Hercules Sander is overheating, consider the following: * You might be forcing the tool to work too fast. Allow the tool to work at its own pace. * The motor housing vents could be blocked. Wear safety goggles and a dust mask/respirator while using compressed air to blow dust out of the motor.
P
Patricia ByrdAug 25, 2025
What to do if my Hercules HD035B is running slowly?
- A
  Alexander NunezAug 26, 2025
  If your Hercules Sander operates slowly, the issue might stem from: * Applying excessive pressure to the workpiece. Decrease the pressure and let the tool do the work. * Low battery pack power. Recharge the battery pack. * A burnt-out battery pack. Replace the battery pack after proper disposal or recycling of the old one.
A
Anna MorrisAug 27, 2025
Why is the performance of my Hercules HD035B decreasing?
- C
  Crystal HubbardAug 28, 2025
  If the performance of your Hercules Sander decreases over time, it could be due to: * Worn or damaged carbon brushes. Have a qualified technician replace the brushes. * A Battery Pack wearing out. Battery Pack capacity will gradually decrease through use. If symptoms are severe, recycle old Battery Pack (or dispose of properly) and replace it.
N
Nathan GillAug 30, 2025
What to do if my Hercules Sander isn't sanding effectively?
- J
  Jane SimonAug 30, 2025
  If your Hercules Sander does not sand effectively, consider these potential causes: * The accessory might be loose. Confirm the accessory spindle is correct. * The accessory could be damaged, worn, or the wrong type for the material. Check the condition and type of the disc accessory, and use only the proper type of accessory in good condition.
J
Jennifer NortonSep 1, 2025
Why is my Hercules HD035B Sander making excessive noise?
- M
  Miss Kimberly DominguezSep 1, 2025
  If your Hercules Sander is making excessive noise or rattling, it could be due to internal damage or wear, such as to the carbon brushes or bearings. In this case, have a technician service the tool.
D
Dr. Amy WoodwardSep 4, 2025
Why Hercules Sander won't start?
- K
  Kathy GomezSep 4, 2025
  The Hercules Sander might not start due to several reasons: * The battery pack may not be properly connected. Remove the battery pack, ensure there are no obstructions, reinsert the battery pack correctly, and press firmly until it locks. * The battery pack might not be charged. Ensure the charger is connected and working, and allow sufficient time for the battery to recharge. * The battery pack could be burnt out. Replace it with a new one after proper disposal or recycling. * There may be internal damage or wear. In this case, have a qualified technician service the sander.
F
fkingSep 7, 2025
What to do if Hercules Sander operates slowly?
- M
  Melissa OchoaSep 7, 2025
  If your Hercules Sander is operating slowly, consider the following: * You might be applying too much pressure to the workpiece. Decrease the pressure and allow the tool to work at its own pace. * The battery pack may have low power. Recharge the battery pack. * The battery pack could be burnt out. Replace the battery pack.
V
Vincent MatthewsSep 9, 2025
Why Hercules Sander is overheating?
- M
  Michael HillSep 9, 2025
  Your Hercules Sander may be overheating due to these reasons: * You might be forcing the tool to work too fast. Allow the tool to work at its own rate. * The motor housing vents could be blocked. Wear safety goggles and a dust mask/respirator, then use compressed air to blow dust out of the motor vents.