EasyManua.ls Logo

HID ProxPro II Reader User Manual

HID ProxPro II Reader
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
español Cableado
* Conexiones opcionales
** El cable de drenaje puede convertirse en una línea de retorno
de datos si se emplea una fuente de alimentación independiente.
A
B
C
D
E
F
G
H
I
J
rojo
negro
verde
blanco
drenaje (drain)
naranja
marrón
amarillo
azul
violeta
CC+ (5-16 VCC)
tierra
datos 0 (datos)
datos 1 (reloj)
**cable blindado c. tierra
*led verde
*led rojo
*señal audible
*retención
*(presencia de tarjeta)
français Schéma de câblage
* connexions facultatives
** Le branchement supplémentaire peut servir de ligne de
« retour de données » en cas d'utilisation d'une alimentation
électrique séparée
A
B
C
D
E
F
G
H
I
J
rouge
noir
vert
blanc
branch. supp.
orange
marron
jaune
bleu
violet
+cc (5-16 V cc)
terre
données 0 (“data”)
données 1 (“clock”)
**mise à la terre blindée
*voyant vert
*voyant rouge
*bip
*attente
*(carte présente)
português Diagrama de ligações
* conexões opcionais
**O fio do dreno pode ser a linha de “retorno de dados”
quando usada uma fonte de energia separada.
A
B
C
D
E
F
G
H
I
J
vermelho
preto
verde
branco
dreno
laranja
marrom
amarelo
azul
violeta
CA+ (5-16 V CA)
terra
Dados 0 (dados)
Dados 1 (clock)
**terra do gabinete
*LED verde
*LED vermelho
*bíper
*reserva
*(placa presente)
deutsch Schaltplan
* optionale Verbindungen
** Drainanschluss kann bei Verwendung separater Stromzufuhr
Datenrückleitung sein
A
B
C
D
E
F
G
H
I
J
Rot
Schwarz
Grün
Weiss
Drain
Orange
Braun
Gelb
Blau
Violett
+Gleichstrom (5-16 V)
Erde
Daten 0 (Daten)
Daten 1 (Zeit)
**Schirmerde
*Grüne LED
*Rote LED
*Signal
*Halten
*(Karte vorhanden)
installation
instalación
installation
instalação
installation
installazione
ProxPro
®
II Reader
1
3
preparing
preparación
préparation
preparação
vorbereitung
preparazione
testing
prueba
test
teste
testen
testare
Turn power on
Encienda la unidad
Mettez sous tension
Ligar energia
Strom einschalten
Accendere
Test card
Pruebe la tarjeta
Testez la carte
Placa de teste
Kartentest
Test
* optional connections
** Drain wire can be “data return” line when a separate power
supply is used
A
B
C
D
E
F
G
H
I
J
red
black
green
white
drain
orange
brown
yellow
blue
violet
+DC (5-16 VDC)
ground
Data 0 (data)
Data 1 (clock)
**shield ground
*green LED
*red LED
*beeper
*hold
*(card present)
english Wiring diagram
Pigtail
Entrada
Toron de raccordement
Fio de conexão
Anschlussfaser
(cavo) pigtail
2
connecting
conexión
connexion
conexão
anschluss
connessione
fcc warning
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may cause undesired operation.
For regulatory compliance, the drain wire should be disconnected at the power supply end of the cable.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
The Reader is intended to be powered from a limited power source output of a certified power supply.
* Connessioni opzionali
** Il cavo.....può fare da “ritorno dati” se viene utilizatto un
alimentatore separato
A
B
C
D
E
F
G
H
I
J
rosso
nero
verde
bianco
cavo di terra
arancione
marrone
giallo
blu
viola
+DC (5-16 VDC)
terra
Dato 0 (dato)
Dato 1 (clock)
**Schermo di terra
*Led verde
*Led rosso
*Ronzatore
*Memoria
*(scheda attiva)
italiano Schema di collegamento
proxpro_II_install_manual.indd 1 6/27/06 11:29:13 AM
Question and Answer IconNeed help?

Do you have a question about the HID ProxPro II Reader and is the answer not in the manual?

HID ProxPro II Reader Specifications

General IconGeneral
TypeProximity card reader
Frequency125 kHz
ColorBlack
Housing MaterialPolycarbonate
Output FormatWiegand
Power Supply5-16 VDC
Operating Temperature-30°C to 70°C (-22°F to 158°F)
Card CompatibilityHID Prox
Form FactorWall Mount
Operating Humidity0 to 95% non-condensing

Summary

Installation and Preparation

Preparing for Installation

Steps and considerations before beginning the reader installation process.

Connecting the Reader

Wiring diagram and connection details for the ProxPro II Reader.

Testing the Reader

Procedures for testing the ProxPro II Reader after installation.

Regulatory Compliance

FCC Warning and Compliance

Details on FCC compliance, operating conditions, and modifications.

Product Components and Specifications

Reader Components List

List of items included with the ProxPro II Reader and associated accessories.

Multi-Technology Card Guide

Overview of different card technologies compatible with HID readers.

Reader Specifications

Technical specifications, operating ranges, and company contact information.

Related product manuals