HIK VISION DS-K4H450 Series - User Manual

Title:
DS-K4H250/450/258 series magnetic lock
connect to DS-K2800 series Access Controller
Version:
v1.0
Date:
01/11/2018
Product:
Access Control Device
Page:
1 of 9
DS-K4H250/450/258 series magnetic lock connect to DS-
K2800 series Access Controller
Preparation
Connecting magnetic lock to access controller is mainly applied to swiping card to open the door for
exiting. For magnetic lock and access controller in this document, please check the table below:
Magnetic Lock
Access Controller
DS-K4H250S
DS-K4H250D
DS-K4H450D
DS-K2801
DS-K2802
DS-K2804
DS-K4H258S
DS-K4H258D
Note
This document is simply used to guide users how to wire correctly and ensure access controllers can
control locks.
The access controller model in this document is DS-K2804.
Part 1 is mainly for magnetic lock wiring, and Part 2 and Part 3 are mainly for the situation that users
could get the door status on iVMS-4200 Client.
Notice
1. Please cut off power supply before wiring;
2. Please use a tool to screw magnetic lock screws in following picture, and remove the cover of
magnetic lock, find V+/V- and NO/NC & COM interfaces of magnetic lock in following picture;

HIK VISION DS-K4H450 Series Specifications

General

Model	DS-K4H450 Series
Card Capacity	50, 000
Max User Capacity	50, 000
Operating System	Linux
Network Interface	10/100/1000Mbps Ethernet
Communication Interface	RS-485, Wiegand
Fingerprint Module	Optical Fingerprint Module
LCD Screen	4.3-inch
Working Temperature	-10 °C to +55 °C (14 °F to +131 °F)
Working Humidity	10% to 90% (No Condensing)
Installation	Wall-mounted

Summary

Preparation and Compatibility

Magnetic Lock and Access Controller Compatibility

Lists compatible DS-K4H magnetic locks and DS-K2800 series access controllers for connection.

Safety Precautions Before Wiring

Advises cutting off power before wiring and preparing tools for magnetic lock installation.

Part 1: Lock+ & Lock- Wiring

Interface Descriptions for Access Controllers

Details interface types (Power Supply, Signal Output) for DS-K2800 series controllers.

Wiring DS-K4 H250 S & DS-K4 H258 S

Provides wiring instructions for DS-K4H250S and DS-K4H258S magnetic locks.

Part 2: Lock+;Lock- & NC;COM Wiring

Magnetic Lock LED Status Indicators

Illustrates magnetic lock LED status for Normal (Close Door), Normal (Open Door), and Abnormal states.

Wiring DS-K4 H250 D, DS-K4 H450 D, DS-K4 H258 D

Guides wiring for DS-K4H250D, DS-K4H450D, and DS-K4H258D magnetic locks.

DS-K4 H250 S NC;COM Wiring

Specific wiring instructions for NC/COM interfaces of DS-K4H250S.

Software Configuration with iVMS-4200

Adding Access Controller to iVMS-4200 Client

Steps to add the access controller device to the iVMS-4200 client software.

Configuring Door Magnetic Sensor Settings

Setting Door Magnetic Sensor to 'Remain Closed' in Access Control Parameters.

Verifying Door Status in iVMS-4200

Checking door status and magnetic lock LED status in iVMS-4200 Client.

Part 3: Lock+;Lock- & NO;COM Wiring

DS-K4 H250 S Lock+;Lock- & NO;COM Wiring

Wiring diagram for DS-K4H250S magnetic lock using Lock+/Lock- and NO/COM interfaces.

DS-K4 H250 D & DS-K4 H450 D Wiring

Wiring instructions for DS-K4H250D and DS-K4H450D magnetic locks.