Hilti DD 160 Manual

592 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

DD 160

Deutsch 1

English 20

Nederlands 39

Français 58

Español 78

Português 98

Italiano 117

Dansk 137

Svenska 155

Norsk 173

Suomi 191

Eesti 209

Latviešu 227

Lietuvių 246

Polski 265

Čeština 285

Slovenčina 303

Magyar 322

Slovenščina 341

Hrvatski 359

Русский 377

Українська 398

Български 419

Română 440

Ελληνικά 460

Türkçe 480

ﻋﺮﺑﻲ 498

日本語 517

한국어 535

繁體中文 553

中文 569

Printed: 09.08.2019 | Doc-Nr: PUB / 5069586 / 000 / 08

Table of Contents

Other manuals for Hilti DD 160

Original Operating Instructions84 pages

Questions and Answers:

N
Natalie SchaeferAug 21, 2025
Why won't my Hilti Drill start?
- S
  stephenhartmanAug 22, 2025
  There could be several reasons why your Hilti Drill won't start: * Check for any interruptions in the electrical supply by testing another appliance in the same outlet. * Inspect the supply cord, extension cord, supply cord plug, and PRCD, replacing them if necessary. * The on/off switch may be defective, or there could be a fault in the electronics, in which case you should have the machine repaired by Hilti Service. * If there's water in the motor, allow the drill to dry completely in a warm, dry place.
H
hmartinezAug 23, 2025
What to do if my Hilti Drill diamond core bit doesn’t rotate?
- S
  Steven SpenceAug 23, 2025
  If the diamond core bit on your Hilti Drill isn’t rotating, it might be due to the gear selector not being engaged. Try operating the gear selector until it engages. Alternatively, the diamond core bit may be jammed in the base material. If this is the case, disconnect the supply cord plug from the power outlet. Grip the diamond core bit with a suitable open-end wrench close to the connection end and release the diamond core bit by rotating it.
N
Nicole GarrisonAug 25, 2025
What to do if my Hilti Drill diamond core drilling machine does not start and service indicator flashes?
- T
  Timothy GarciaAug 25, 2025
  If your Hilti Drill diamond core drilling machine does not start and the service indicator is flashing, it could be due to the motor overheating or an overload error. To resolve this, wait a few minutes for the motor to cool down, or let the drill run without any load to speed up cooling. Then, switch the drill off and on again.
A
Adam JenkinsAug 27, 2025
What to do if the diamond core bit can’t be fitted into the chuck of my Hilti Drill?
- A
  Alyssa HallAug 27, 2025
  If you can’t fit the diamond core bit into the chuck of your Hilti Drill, the core bit connection end or chuck is likely dirty or damaged. You should clean and grease these parts or replace them if necessary.
P
psparksAug 27, 2025
What to do if my Hilti Power Tool diamond core bit doesn’t rotate?
- J
  Joshua GarciaAug 27, 2025
  If the diamond core bit on your Hilti power tool isn't rotating, consider these possibilities: * The gear selector isn’t engaged. Operate the gear selector until it engages. * The diamond core bit has become jammed in the base material. Disconnect the supply cord plug from the power outlet. Grip the diamond core bit with a suitable open-end wrench close to the connection end and release the diamond core bit by rotating it. * If the above solutions don't work, the gearing may be defective. Have the machine repaired by Hilti Service.
K
Karen BrownAug 29, 2025
What to do if the drilling speed of my Hilti Drill is decreasing?
- C
  Corey ShafferAug 29, 2025
  A decrease in drilling speed of your Hilti Drill can stem from various factors: * The diamond core bit may be polished, requiring sharpening by drilling into a sharpening plate. * Ensure the core bit specification is correct for the base material. * Adjust the water flow rate if it's too high or too low. * Remove any core stuck in the diamond core bit. * If the maximum drilling depth is reached, remove the core and use a core bit extension. * Inspect the diamond core bit for damage and replace if needed. * Release the brake, if applied. * For high steel content, select a more suitable diamond core bit specification. * If the safety clutch disengages too soon or is slipping, have the machine repaired by Hilti Service.
B
Brent CruzAug 30, 2025
What to do if my Hilti Drill diamond core drilling machine does not start and theft protection indicator flashes?
- M
  Mrs. Nicole Brown MDAug 31, 2025
  If your Hilti Drill doesn't start and the theft protection indicator is flashing, it means the machine hasn't been unlocked. Use the TPS key to unlock it.
L
Laura MorrisSep 1, 2025
What does it mean if the service indicator shows on my Hilti Drill?
- S
  Sylvia AdamsSep 1, 2025
  If the service indicator is illuminated on your Hilti Drill, it signifies that the carbon brush wear limit is nearly reached. It's recommended to have the carbon brushes replaced soon.
C
ccervantesSep 2, 2025
What to do if my Hilti Drill diamond core drilling machine does not start and service indicator lights up?
- M
  Marc JonesSep 2, 2025
  If your Hilti Drill doesn't start and the service indicator lights up, the carbon brushes are likely worn out and need to be replaced.
G
gzunigaSep 4, 2025
What to do if the handwheel on my Hilti Drill can be turned without resistance?
- E
  Eric KruegerSep 4, 2025
  If the handwheel on your Hilti Drill turns without resistance, the split pin is likely broken and needs to be replaced.

Hilti DD 160 Specifications

General

Power	2200 W
Speed 1	510 rpm
Water supply connection	Yes
Rated Voltage	230 V
Rated Current	10 A
Rated Input	2200 W
Voltage	230 V
Chuck Type	BI+

Related product manuals

Preview: Hilti DD-750 HY

Hilti DD-750 HY

Preview: Hilti DX 6

Preview: Hilti DX 5

Preview: Hilti DX 36

Preview: Hilti DX 450

Preview: Hilti DX36 M

Preview: Hilti DC-SE20

Preview: Hilti TE DRS-6-A

Hilti TE DRS-6-A

Preview: Hilti DCH 150-SL

Hilti DCH 150-SL

Preview: Hilti DX 6 Series

Hilti DX 6 Series