To Next PageTo Next PageWhat to do if Hilti PD 38 application software establishes no connection to PD 38 after installation?
If the Hilti PD 38 application doesn't connect to the PD 38 after installation, try the following: First, switch on the PD 38. Check that your PDA is equipped with Bluetooth. Reduce the distance between the PDA/MDA and the PD 38. As a last resort, reset the PDA.
What to do if there is no connection between PDA/MDA and PD 38 when Hilti PD 38 application is started?
If there's no connection between your PDA/MDA and the PD 38 when the Hilti PD 38 application starts, try these steps: Ensure the PD 38 is switched on and that Bluetooth is enabled on the PD 38. Reduce the distance between the PDA/MDA and PD 38. Try switching off Bluetooth on the PDA/MDA and restarting the Hilti PD 38 application on the PDA. If problems persist, consider resetting the PDA.
What to do if no measurements transferred but PDA and PD 38 Hilti Measuring Instruments are connected?
If your PDA and PD 38 are connected, but measurements aren't transferring, try these solutions: Check the serial numbers to ensure you're connected to the correct PD 38. Reduce the distance between the PDA/MDA and PD 38. If the issue persists, reset the PDA.
What to do if PDA/MDA Hilti Measuring Instruments doesn’t react?
If your PDA/MDA isn't responding, try resetting it.
What to do if data is transferred but no longer visible in Hilti PD 38?
If data is transferred but not visible, check the folders where the files are stored and check the folder before copying.
How to fix no connection between PDA/MDA and PC Hilti PD 38?
To resolve connection issues between your PDA/MDA and PC, check the cable connection between the docking station and the PC. If the problem continues, restart your PC.
What to do if there are no measurements in data table of Hilti PD 38?
To display measurements in the data table, activate the “Hilti Measuring Interface”.
General| Accuracy | ± 1.0 mm |
|---|---|
| Laser Class | Class 2 |
| IP Protection Class | IP 54 |
| Power Supply | 2 x AA batteries |
| Operating temperature range | -10 °C to 50 °C |
| Functions | Distance measurement, area calculation, volume calculation, Pythagoras function |
Explains the meaning of warning symbols like CAUTION and NOTE in the manual.
Outlines the range meter's purposes: measuring distances, calculating areas, volumes, and adding/subtracting distances.
Describes the general functions and components of the range meter, including display and buttons.
Explains Bluetooth technology for wireless data exchange and its typical transmission range.
Specifies power requirements: 3 V DC, AA batteries (alkaline or rechargeable NiMH).
Details the measuring range from 0.05 m to 200 m, including typical ranges for different surfaces.
States typical accuracy of ±1.5 mm and how atmospheric conditions affect it.
Lists the basic operating modes: Single measurement, Continuous measurement, Calculation/functions.
Specifies laser details: Visible, 620-690 nm, class 2, output power < 1 mW.
General safety precautions to be observed at all times in addition to section-specific safety notices.
Warns against improper use of the range meter and accessories, including unauthorized opening and modification.
Provides precautions for checking for damage, acclimatization, careful handling, and cleaning of the range meter.
Advises on securing the work area, avoiding hazardous body positions, and observing accident prevention regulations.
Explains laser class 2 classification, eye safety, and how eyelid reflex protects users.
Instructs on inserting batteries, observing polarity, and ensuring the compartment is locked.
Explains standard battery charging, ensuring no memory effect and allowing charging at any time.
Details the standard battery charging process, including the use of the charging adapter and mains/car plugs.
Explains how to switch the range meter on and off using the 'On/Off' button.
Guides through the first distance measurement, aiming at a target and pressing the measure button.
Explains how to toggle Bluetooth on/off using the volume button and indicates connection status.
Provides an overview of the range meter's control panel and buttons.
Discusses taking measurements to stationary targets, and limitations with reflective surfaces.
Guides through the step-by-step process of taking a distance measurement.
Details the procedure for performing a single distance measurement using the 'Measure' button.
Explains how to determine areas quickly by pressing the 'Area' function button.
Explains how to determine volumes in one measuring operation by pressing the 'Volume' function button.
Explains how to establish a Bluetooth connection between the PD 38 and PDA/MDA.
Describes using the PD 38 with a PDA/MDA via Bluetooth for measurements, noting disabled onboard functions.
Explains how to perform self-inspection and testing of the range meter for accuracy.
Recommends regular checks through Hilti calibration service for reliability and legal compliance.
