How to fix Hilti PR 30-HVS A12 tool if it doesn't work?
If your Hilti Measuring Instruments tool isn't working, ensure the battery is fully inserted until you hear an audible click. Also, check if the battery is low and replace or charge it if necessary.
What to do if Hilti PR 30-HVS A12 Measuring Instruments battery doesn’t engage with an audible click?
If the battery doesn’t engage with an audible click on your Hilti Measuring Instruments, clean the retaining lugs on the battery and refit the battery.
What to do if Hilti Measuring Instruments rotating laser has low battery?
If the rotating laser has a low battery, charge the battery of your Hilti Measuring Instruments.
What to do if Hilti PR 30-HVS A12 Measuring Instruments tool or battery gets very hot?
If the Hilti Measuring Instruments tool or battery gets very hot, immediately switch off the tool, remove the battery, keep it under observation, allow it to cool down and contact Hilti Service due to a possible electrical fault.
Why does Hilti PR 30-HVS A12 Measuring Instruments battery run down quickly?
If the battery of your Hilti Measuring Instruments runs down more quickly than usual, it might be due to a very low ambient temperature. Warm up the battery slowly to room temperature.
What to do if Hilti PR 30-HVS A12 command is not possible?
If the command is not possible and there is no reaction from your Hilti Measuring Instruments, check that all devices are switched on and within direct range. Then, repeat the entry.
General| Type | Rotating Laser |
|---|---|
| Accuracy | ±0.5 mm at 10 m |
| Self-leveling Range | ±5° |
| Laser Class | Class 2 |
| Laser Class Details | IEC 60825-1:2014 |
| Protection Class | IP66 |
| Battery Voltage | 12 V |
| Battery Type | Li-ion |
| Power Supply | Li-ion battery |
| Rotation Speed | 600 rpm |
| Operating Temperature | -20 to +50 °C |
Prerequisite for safe handling and use. Observe safety instructions.
Explains warning signals (DANGER, WARNING, CAUTION) and symbols used in the document.
Symbols found on the product, including wireless transmission and battery indicators.
Details about laser classification and safety notes.
Type designation, serial number, and product information.
Statement of compliance with directives and standards.
Essential safety rules and precautions for operation.
Rules for safe operation, environment, and handling.
Procedures for preparing the work area safely.
Information on EMC compliance and potential interference.
Safety guidelines for Class 2 laser products.
Detailed safety instructions for handling batteries.
Identifies main components of the laser and receiver.
Explains controls and indicators on the laser.
Explains controls and display of the receiver.
Describes the product's purpose and applications.
Details operational features like auto-leveling, alignment, and switch-off.
Explains auto-leveling and automatic alignment functions.
Details inclination settings and vertical plane surveillance.
Explains auto-switch-off and shock warning functions.
Explains receiver distance indication and remote control use.
Instructions for pairing accessories wirelessly.
Table of LED statuses and their meanings.
Explains the battery charge indicator LEDs.
Lists the contents of the package.
Detailed technical specifications for the rotating laser.
Detailed technical specifications for the laser receiver.
Safety and preparation steps before operation.
Correct procedures for handling the laser and battery.
Step-by-step guide for battery handling with safety.
How to switch on and start horizontal laser operation.
Guide for manual horizontal alignment.
Guide for automatic horizontal alignment.
Instructions for manual vertical alignment.
Guide for automatic vertical alignment.
Setting inclination using PRA 79 adapter.
Steps for manually setting inclination.
Guide for automatically setting inclination.
Using electronic alignment for precision.
How to disable the shock warning function.
How to enable/disable sleep mode.
Procedure to verify horizontal axis accuracy.
Procedure to verify vertical axis accuracy.
General operation of the laser receiver.
Steps for pairing the laser and receiver.
Steps for pairing the tripod and receiver.
How the receiver detects the laser beam.
How to set units (metric/imperial).
How to change units for accuracy settings.
How to control the receiver's audio feedback volume.
How to configure signal tone settings.
Overview of menu options available on the PRA 30 receiver.
Setting measurement units.
Shows current software version.
Activating/deactivating sleep mode.
Setting inclination units (% or degrees).
Status and cancellation of pairing with laser.
Status and cancellation of pairing with tripod.
Adjusting shock warning sensitivity.
Turning wireless connection on/off.
Instructions for using the PRA 83 holder.
Procedures for cleaning the tool and batteries.
Regular checks for damage and functionality.
How to clean the laser exit window.
Details on Hilti service and recalibration.
Importance of regular accuracy checks.
Safety guidelines for transporting and storing tools/batteries.
Table of common faults, causes, and solutions.
Solutions for pairing, sleep mode, and low battery.
Information on hazardous substances compliance.
Warnings and instructions for proper disposal.
To Next Page
