Hilti TE 60-AVR - User Manual

Other manuals for Hilti TE 60-AVR

Operating Instructions20 pages

Original Operating Instructions72 pages

Questions and Answers

D
Douglas DavisSep 12, 2025
What to do if my Hilti Power Tool does not start?
- R
  Robert FreemanSep 12, 2025
  If your Hilti Power Tool doesn't start, consider these possible causes and solutions: * Check for an interruption in the electric supply by plugging in another electric tool or appliance to see if it works. * If the electronic restart interlock is activated after a power interruption, switch the tool off and then on again. * Inspect the supply cord or plug for defects and have it checked and replaced by a trained electrical specialist if necessary. * Ensure the detachable supply cord is correctly fitted to the power tool. * If using a generator with sleep mode, apply a load by connecting a second power consumer (e.g., worklight), then switch the tool off and on again.
G
gregory19Aug 23, 2025
How to release a stuck drill bit from Hilti Tools?
- B
  Bradley HarperAug 23, 2025
  If the drill bit cannot be released from your Hilti Tools product, ensure that the chuck is pulled back fully. Pull the tool lock back as far as it will go and remove the accessory tool. Also, check if the side handle is fitted correctly. Release the side handle and refit it correctly so that the clamping band and side handle engage in the recess.
L
Lori WolfeAug 25, 2025
How to release a stuck drill bit from my Hilti Power Tool?
- E
  Emily HarrisAug 25, 2025
  If you're having trouble releasing the drill bit from your Hilti Power Tool: * Pull the chuck back as far as it will go and then try to remove the accessory tool. * Check the side handle. Release it and refit it correctly so that the clamping band and side handle engage in the recess.
J
Jessica MedinaAug 27, 2025
What to do if my Hilti TE 60-AVR Drill does not start?
- K
  Kelli KingAug 27, 2025
  If your Hilti Drill doesn't start, first, ensure there isn't an interruption in the electric supply by testing another appliance in the same outlet. If that's not the issue, the electronic restart interlock may be activated due to a recent power interruption; try switching the drill off and on again. Check the supply cord and plug for any defects, and if found, have them inspected and replaced by a trained electrical specialist. Also, make sure the detachable supply cord is correctly fitted. Finally, if you're using a generator, it might be in sleep mode; apply a load by connecting another device like a work light, then switch the drill off and on again.
W
warrenjackAug 27, 2025
Why is my Hilti TE 60-AVR not developing full power?
- T
  Tim CortezAug 27, 2025
  If your Hilti Drill isn't developing full power, there are several potential causes. First, ensure that the extension cord you're using is of an approved length and adequate gauge. Next, check that the control switch is fully pressed down. Also, verify that the voltage provided by the electric supply is sufficient. Finally, make sure the reduced-power button is not engaged; if it is, press the button to disengage it.
M
mariaperryAug 29, 2025
What does it mean when the service indicator light is on for Hilti TE 60-AVR?
- Y
  yangwilliamAug 29, 2025
  If your Hilti Drill's service indicator lights up, it means the carbon brushes are worn. To resolve this, have the product checked by a trained electrical specialist, and have the carbon brushes replaced if necessary.
N
Nicole AlvaradoSep 18, 2025
Why doesn't the drill bit rotate on my Hilti Power Tool?
- S
  soniagardnerSep 18, 2025
  If the drill bit isn't rotating on your Hilti Power Tool, the function selector switch may not be correctly engaged, is set to 'Chiseling', or is set to 'Chisel positioning'. Move the function selector switch to the 'Hammer drilling' position while the motor is not rotating.
M
Mason ShawSep 9, 2025
What does it mean when the service indicator blinks on Hilti Tools?
- J
  josephpatriciaSep 9, 2025
  If the service indicator is blinking on your Hilti Tools product, it indicates damage to the product or that the service limit time has been reached. Have the product repaired by Hilti Service.
J
Joshua CarterSep 6, 2025
What does it mean when the service indicator lights up on Hilti Tools?
- J
  Judith HinesSep 6, 2025
  If the service indicator light is on for your Hilti Tools product, the carbon brushes are likely worn. Have the product checked by a trained electrical specialist and have the carbon brushes replaced, if necessary.
R
Ricardo CooperSep 7, 2025
Why is the drill bit not rotating on my Hilti Tools?
- A
  angela98Sep 7, 2025
  If the drill bit isn't rotating on your Hilti Tools product, the function selector switch may not be correctly engaged, or it might be set to “Chiseling” or “Chisel positioning”. Move the function selector switch to the “Hammer drilling” position while the motor is not rotating.