EasyManua.ls Logo

Hisun HS394-2 - User Manual

Hisun HS394-2
68 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
IntroductionHS3942/HS2942
11
INTRODUCTION
Congratulations on your purchase of the HS394-2/HS294-2. This Owner’s / Operator’s
manual will provide you information regarding safe operation, operational instructions,
maintenance and care. Fully understanding this manual and following all of the instructions
herein will provide the knowledge needed to have safe and enjoyable vehicle operation.
If you have any questions regarding the operation or maintenance of your UTV, please
call Monkija Trail Park Oy at 0086-23-61020546 or go to Pajalantie 6a 37550, Lempaala,
Finland.
IMPORTANT SAFETY MESSAGES
READ THIS MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATING YOUR UTV.
MAKE SURE YOU UNDERSTAND ALL INSTRUCTIONS.
PAY CLOSE ATTENTION TO THE WARNING AND CAUTION LABELS ON THE UTV.
NEVER OPERATE THE UTV WITHOUT PROPER TRAINING OR INSTRUCTION.
THIS UTV SHOULD NOT BE RIDDEN BY ANYONE UNDER
16 YEARS OF AGE.

Table of Contents

Questions and Answers

  • C
    Charles EstradaAug 15, 2025
    What to do if my Hisun HS394-2 Utility Vehicle engine overheats?
    • T
      Thomas RodriguezAug 15, 2025
      If your Hisun Utility Vehicle engine is overheating, it could be due to several factors. First, check if the engine is overloaded and shift to a lower gear or reduce the load. Ensure the coolant level is adequate and inspect the radiator and hoses for leaks. Verify that the motor-driven fan is functioning and that its fuse isn't blown, and check the electric system. Also, make sure the radiator core or grille screens are free from debris. If the coolant flow route is corroded, flush the cooling system.
  • J
    James Carlson MDAug 18, 2025
    What causes insufficient engine power in my Hisun Utility Vehicle?
    • R
      Rachel CarterAug 19, 2025
      Insufficient engine power in your Hisun Utility Vehicle can stem from several issues. Check the fuel system for any insufficiencies. A clogged injector can also reduce power, so clean or replace it. Other potential causes include a bad crankshaft position sensor (replace it), a clogged air cleaner (clean or replace it), a dirty or fouled spark plug (clean or replace it), or a bad ignition coil (replace it).
  • R
    Ronald GutierrezAug 21, 2025
    What causes transmission noise in my Hisun HS394-2 Utility Vehicle?
    • J
      Jesse GarrettAug 22, 2025
      Transmission noise in your Hisun Utility Vehicle can be caused by a big matching clearance for the inner and outside gears of the transmission shaft, a big clearance of transmission gears, or a non-good connection of the gear end face. In each of these cases, replace the gears.
  • J
    Jessica ShermanAug 26, 2025
    What to do if my Hisun HS394-2 has less vehicle power?
    • A
      Alyssa BuckAug 26, 2025
      If your Hisun Utility Vehicle has less power, check if the parking brake is engaged and loosen the lay-up rod if necessary. For non-full uncoupling of the disc brake, or if there is CVT transmission sliding, contact the distributor. If sliding is the issue, try removing the grease from the clutch or replacing the CVT transmission belt or the clutch.
  • F
    fosteremilyAug 28, 2025
    What to do if my Hisun HS394-2 has no good brake or noise?
    • R
      Rebecca HoAug 28, 2025
      If your Hisun Utility Vehicle has no good brake or noise, check the braking oil level. If there is air inside the braking system, brake discs abrasion, contact the distributor. Ensure the assembling bolt of the disc plate and assembling bolt for disc brake clippers are not loose and lock tightly if necessary.
  • B
    Brandon TateSep 1, 2025
    What causes terminals to corrode and heat up on my Hisun HS394-2 Utility Vehicle?
    • C
      Cory BaldwinSep 1, 2025
      Severely corroded and heated terminals on your Hisun Utility Vehicle are typically due to a poor terminal connection. Clean the terminal and tighten it securely.
  • J
    Jeffrey PalmerSep 4, 2025
    What causes non agility for gearshift in Hisun HS394-2 Utility Vehicle?
    • K
      Kevin CooperSep 4, 2025
      Non agility for gearshift in Hisun Utility Vehicle can be caused by several factors, including high idling speed of the engine. In this case, replace the throttle cable, throttle petal, or the throttle. High rotary speed for clutch connection can also be a factor, so replace the junior clutch spring or the primary clutch. If there is non good adjust for gearshift stay wire, put the gearshift rod into the position of “N”, put the gearshift arm of engine into ”N”, adjust the stay wire and the bolt, and lock tightly. Gear abrasion can also cause this issue, so replace the gears.
  • S
    susanharrisSep 7, 2025
    Why does my Hisun Utility Vehicle battery electrolyte level drop rapidly?
    • T
      Timothy BrownSep 7, 2025
      A rapid drop in the battery electrolyte level in your Hisun Utility Vehicle could be due to a crack or pinholes in the electrolytic cells, in which case you should replace the battery. It could also be caused by charging system trouble, for which you should consult your local dealer.
  • L
    lori55Sep 12, 2025
    Why is recharging impossible on my Hisun HS394-2 Utility Vehicle battery?
    • A
      Aaron MartinezSep 12, 2025
      Recharging may be impossible on your Hisun Utility Vehicle battery if the battery life has expired. Replace the battery.

Summary

Introduction to HS394-2;HS294-2

Safety Messages and Manual Information

Covers essential safety warnings and the importance of understanding the owner's manual for safe operation.

Notices, Symbols, and Layout

Details important notices, universal symbols, vehicle parts location, and illustrated contents.

Safe Operation Guidelines

Operation Rules and Driving Techniques

Provides safety instructions, general operation, children safety, and driving tips for various conditions.

Parking, Transport, and Warnings

Covers parking procedures, vehicle transportation, maintenance basics, and warning label information.

Vehicle Servicing and Specifications

Identification, Limitations, and Specifications

Details vehicle identification, limitations, and technical specifications for performance and capacity.

Operation Procedures

Pre-Operation and Engine Operation

Covers pre-operation checks, starting, stopping, and warming up the engine.

Vehicle Controls and Gauges

Explains new vehicle break-in, operating procedures, controls, switches, and instrument panel gauges.

Maintenance and Adjustment

Winch Mount Plate and Transporting Vehicle

Covers winch mount plate installation and guidelines for transporting the vehicle safely.

Service Intervals and Schedules

Details recommended service intervals for various maintenance tasks and checks.

Periodic Service Procedures

Adjustments: Seat, Steering, Cargo, Shocks

Guides on adjusting seat, steering wheel, cargo bed, and shock absorbers for optimal performance.

Checks and Replacements: Fluids, Brakes, Tires

Covers daily checks, fluid levels, brake system maintenance, and tire condition.

Air Cleaner, Battery, and Storage

Details cleaning air cleaner, battery maintenance, and procedures for vehicle storage.

Troubleshooting Vehicle Issues

Engine and Battery Problems

Addresses common engine starting issues, power loss, overheating, and battery malfunctions.

Diagnostic Codes and Machine Issues

Lists diagnostic trouble codes and troubleshooting for gearshift, transmission, and brakes.

Options and Safety Declarations

Vehicle Options

Lists optional accessories available for the vehicle.

Safety Declarations

Provides declarations on driver's noise exposure and vibration levels according to EU standards.

Hisun HS394-2 Specifications

General IconGeneral
BrandHisun
ModelHS394-2
CategoryUtility Vehicle
LanguageEnglish

Related product manuals