MODE SELECTOR
AUTO
HEAT
DEHUMIDIFY
COOL
FAN
FAN SPEED
AUTO
SILENT
LOW
MED
HIGH
START / STOP
ECO SENSOR
FAN
POWERFUL
Precautions for Use
●
Do not put the remote controller in the following places.
●
Under direct sunlight.
●
In the vicinity of a heater.
●
Handle the remote controller carefully. Do not drop it on the floor, and protect it from water.
●
Once the outdoor unit stops, it will not restart for about 3 minutes (unless you turn the power switch
off and on or unplug the power cord and plug it in again).
This is to protect the device and does not indicate a failure.
●
If you press the MODE selector button during operation, the device may stop for about 3 minutes for
protection.
MODE selector Button
Use this button to select the
operating mode. Every time you
press this button, the mode will
change from
(AUTO) ➞
(HEAT) ➞ (DEHUMIDIFY) ➞
(COOL) ➞
(FAN) ➞
(FILTER CLEAN) cyclically.
(FILTER CLEAN) can be
selected when the unit is OFF.
LIGHT ON/OFF Button
Use this button to set the
LIGHT ON/OFF mode. (
NAMES AND FUNCTIONS OF REMOTE CONTROLLER
INFO
SLEEP TIMER
LIGHT ON/OFF
AUTO SWING (VERTICAL)
AUTO SWING (HORIZONTAL)
LEAVE HOME
FROST WASH
FILTER CLEAN
DAY
PROGRAM NO.
ON / OFF TIMER
TIME
OK
DELETE
COPY / PASTE
CANCEL
SEND
CLOCK
p. 18)
POWERFUL Button
Use this button to set the
POWERFUL mode. (
p. 17)
INFORMATION Button
(
p. 29)
FROST WASH Button
( p. 1)
LEAVE HOME Button
(
p. 19)
ECO SLEEP TIMER Button
Use this button to set the ECO
sleep timer. (
p. 21)
ON / OFF TIMER setting Buttons
(
p. 20)
WEEKLY TIMER setting Buttons
(
p. 23)
AUTO SWING (Vertical) Button
Controls the angle of the
horizontal air deflector. ( p. 1 )
AUTO SWING (Horizontal) Button
Controls the angle of the vertical
air deflector. ( p. 1 )
AUTOMATIC OPERATION
The device will automatically determine the mode of operation, HEAT or COOL depending on the current
room temperature. The selected mode of operation will change when the room temperature varies.
VARIOUS FUNCTIONS
■ Auto Restart Control
● If there is a power failure, operation will be automatically restarted when the power is resumed with previous operation
mode and airflow direction.
(As the operation is not stopped by remote controller.)
● If you intend not to continue the operation when the power is resumed, switch off the power supply.
When you switch on the circuit breaker, the operation will be automatically restarted with previous operation mode
and airflow direction.
Note: 1. If you do not require Auto Restart Control, please consult your sales agent.
2. Auto Restart Control is not available when Timer or Sleep Timer mode is set.
■ As the settings are stored in the memory of the remote controller, you
only have to press the
(START/STOP) button next time.
Press the MODE selector button so that the display indicates the
(AUTO) mode of operation.
● When AUTO has been selected, the device will automatically
determine the mode of operation, HEAT or COOL depending on
the current room temperature.
● If the mode automatically selected by the unit is not satisfactory,
manually change the mode setting (HEAT, DEHUMIDIFY, COOL
or FAN).
Press the
(START/STOP) button.
Operation starts with a beep.
Press the button again to stop operation.
Set the desired room temperature with the TEMPERATURE buttons
(the display indicates the setting).
The temperature setting and the actual room temperature may vary
depending on conditions.
START
STOP
1
2
3
Set the desired FAN SPEED with the (FAN SPEED) button (the
display indicates the setting).
(AUTO) (HIGH) (MED)
(SILENT) (LOW)
NOTE：
After the unit starts the automatic operation(including the operation by
temporary switch), the cooling and heating lamps light up for a few seconds
at the same time to determine the mode of operation, and then the one of
heating or cooling lamp lights off. It's not a machine failure.
To Next Page
Loading...
