Hitachi SJ Series - Page 29

Chapter 3
Only operating
shown here.
Refer to “Chapter 10 Test Runs” for details.
The motor does not rotate!
An error indication appears on the inverter.
See
“Chapter 18 Tips/FAQ/Troubleshooting”.
How to reduce noise, suppress harmonics and increase
regenerative potential.
See “Chapter 7 Wire Connection and Optional Devices”.
How to run our inverter with communications.
See “Chapter 14 RS485
Menu
STOP
Output frequency
Main speed command
(Operator keypad)
FA-
01
3.2.5 Prepare for Rotating the Motor
3.2.6 Troubleshooting
C
onfirm that the FW or RV indicator
is displayed.
⇒
[AA111]=02
Press the right key to move
forward a screen while
pressing the O key to confirm
the setting.
Ex. Change [FA
Chapter 3
Only operating
procedures using the operator keypad are
Refer to “Chapter 10 Test Runs” for details.
The motor does not rotate!
An error indication appears on the inverter.
“Chapter 18 Tips/FAQ/Troubleshooting”.
How to reduce noise, suppress harmonics and increase
regenerative potential.
See “Chapter 7 Wire Connection and Optional Devices”.
How to run our inverter with communications.
See “Chapter 14 RS485
Communication”.
0.00 Hz
oFW
Output frequency
Main speed command
(Operator keypad)
01
3.2.5 Prepare for Rotating the Motor
3.2.6 Troubleshooting
onfirm that the FW or RV indicator
is displayed.
[AA111]=02
Press the right key to move
forward a screen while
pressing the O key to confirm
the setting.
Ex. Change [FA
-01].
You Can Run the Inverter after Reading This Chapter
procedures using the operator keypad are
Refer to “Chapter 10 Test Runs” for details.
The motor does not rotate!
An error indication appears on the inverter.
“Chapter 18 Tips/FAQ/Troubleshooting”.
How to reduce noise, suppress harmonics and increase
See “Chapter 7 Wire Connection and Optional Devices”.
How to run our inverter with communications.
Communication”.
0.00 Hz
M1
0.00 Hz
Main speed command
(Operator keypad)
0.00 Hz
[0.00-
60.00]
3.2.5 Prepare for Rotating the Motor
3.2.6 Troubleshooting
Ready to operate! Press the Run button to accelerate the motor.
onfirm that the FW or RV indicator
Press the right key to move
forward a screen while
pressing the O key to confirm
You Can Run the Inverter after Reading This Chapter
procedures using the operator keypad are
Refer to “Chapter 10 Test Runs” for details.
An error indication appears on the inverter.
“Chapter 18 Tips/FAQ/Troubleshooting”.
How to reduce noise, suppress harmonics and increase
See “Chapter 7 Wire Connection and Optional Devices”.
How to run our inverter with communications.
Communication”.
Menu
oFW
STOP
Output frequency
Output current
Input terminal
----
H03
0.00 Hz
0.00 Hz
60.00]
3.2.5 Prepare for Rotating the Motor
Ready to operate! Press the Run button to accelerate the motor.
Press the up, down,
left, or right key to
change data while
pressing the O key
to make the setting.
Confirm that a
command is sent out
from the operator
keypad.
3-4
You Can Run the Inverter after Reading This Chapter
procedures using the operator keypad are
How to reduce noise, suppress harmonics and increase
See “Chapter 7 Wire Connection and Optional Devices”.
How to operate the operator
See “Chapter 9 Operating Instructions”.
How to run our inverter using external signals.
See “Chapter 10 Test Runs” and “Chapter 11
Examples of Settings by Operation Command
Destination”.
How to use the inverter functions.
How to monitor the
See “Chapter 12 Inverter Functions” and “Chapter 13
Information Monitoring Functions”.
60.00 Hz
oFW
Output frequency
Output current
LLLLLLLLLLL
Input terminal
monitor
Ready to operate! Press the Run button to accelerate the motor.
Press the up, down,
left, or right key to
change data while
pressing the O key
to make the setting.
Confirm that a
command is sent out
from the operator
keypad.
⇒
[AA101]=07
You Can Run the Inverter after Reading This Chapter
How to operate the operator
See “Chapter 9 Operating Instructions”.
How to run our inverter using external signals.
See “Chapter 10 Test Runs” and “Chapter 11
Examples of Settings by Operation Command
Destination”.
How to use the inverter functions.
How to monitor the
See “Chapter 12 Inverter Functions” and “Chapter 13
Information Monitoring Functions”.
Optional
device
60.00 Hz
M1
H01
0.00 Hz
0.00 A
LLLLLLLLLLL
monitor
Menu
STOP
Output Frequency
Main speed command
(Operator keypad)
F
A
Ready to operate! Press the Run button to accelerate the motor.
Make sure that the
is
not displayed
Press the up, down,
left, or right key to
change data while
pressing the O key
to make the setting.
command is sent out
from the operator
[AA101]=07
You Can Run the Inverter after Reading This Chapter
How to operate the operator
See “Chapter 9 Operating Instructions”.
How to run our inverter using external signals.
See “Chapter 10 Test Runs” and “Chapter 11
Examples of Settings by Operation Command
How to use the inverter functions.
How to monitor the
operating status.
See “Chapter 12 Inverter Functions” and “Chapter 13
Information Monitoring Functions”.
Optional
device
H01
0.00 Hz
0.00 A
LLLLLLLLLLL
Menu
oFW
STOP
Output Frequency
Main speed command
(Operator keypad)
A
-01
Ready to operate! Press the Run button to accelerate the motor.
Confirm that the command
frequency is at the desired
value.
⇒
(Ex.)
Make sure that the
NRDY
not displayed
.
You Can Run the Inverter after Reading This Chapter
How to operate the operator
keypad.
See “Chapter 9 Operating Instructions”.
How to run our inverter using external signals.
See “Chapter 10 Test Runs” and “Chapter 11
Examples of Settings by Operation Command
How to use the inverter functions.
operating status.
See “Chapter 12 Inverter Functions” and “Chapter 13
Information Monitoring Functions”.
60.00 Hz
M1
0.00 Hz
Output Frequency
Main speed command
(Operator keypad)
60.00 Hz
[0.00
Confirm that the command
frequency is at the desired
value.
(Ex.)
[FA-
01]=60.00Hz
NRDY
indicator
You Can Run the Inverter after Reading This Chapter
How to run our inverter using external signals.
See “Chapter 10 Test Runs” and “Chapter 11
Examples of Settings by Operation Command
See “Chapter 12 Inverter Functions” and “Chapter 13
----
H03
0.00 Hz
60.00 Hz
[0.00
-
60.00]
Confirm that the command
frequency is at the desired
01]=60.00Hz
indicator
You Can Run the Inverter after Reading This Chapter