Hitachi Super drive series - User Manual

Operating Instructions
OPERATION
1. Check Driver Bit to make sure it is in good con-
dition.
• If it is broken or worn out, install a new one.
2. IMPORTANT! Make sure the forward-reverse
switch is in the forward position.
3. Insert a strip of screws into the feed track. Pull
it through and insert the front into the index mod-
ule until the first screw is in driving position in the
center of the nose piece. See Figure 1.
FIGURE 1.
4. Adjust the nosepiece so there is a 1/8” to 1/4”
gap between nose piece and tip of screw.
• Tighten the nosepiece screw securely. See
Figure 2.
5. Follow instructions on the sticker. Push slider in
to adjust. Then turn knob until it locks.
FIGURE 2.
FIGURE 3.
6. Turn on the motor before starting to drive
screws.
• The motor can be locked to the ON position.
HITACHI SuperDrive Auto-feed Screw System
WARRANTY
HITACHI SuperDrive tools and system components are warranted to the original purchaser at retail to be free from defects
in material and workmanship one year from the date of purchase.
The warranty shall only cover defects and not normal wear and tear, which occurs with use.
HITACHI SuperDrive assumes no responsibility whatsoever for malfunctions, failures or defects resulting from misuse,
abuse, neglect, alteration or modification. SuperDrive makes no warranty and shall not be liable as to the fitness of its tools
or fasteners for any particular uses or applications. No other warranties, representations or promises as to the quality or
performance of the SuperDrive fastening tool other than those contained herein are made.
ANY IMPLIED WARRANTY GRANTED UNDER STATE LAW, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO DURATION TO THE EXPRESS WARRANTY GRANTED HEREUNDER. SUPER-
DRIVE IN NO EVENT SHALL BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
For SuperDrive 75 Series
Appx. 1/4”
Call 1-800-706-7337 or your sales rep. for replacement parts.
PARTS LIST - 75 SERIES TOOL QTY
725414 MODULE (GREEN DOT) 1
725415 SPRING (GREEN) 1.7mm 1
725413 NOSEPIECE FLAT HEAD SCREW
M4x10mm 1
725470 NOSEPIECE SUBFLOOR AND
METAL-TO-METAL 1
725471 NOSEPIECE DECK/DRYWALL 1
725425 END PLATE FOR 75 1
725424 WING SCREW FOR END PLATE 1
725423 BODY HEX SOCKET CAP SCREW
M4x8 1
725422 BODY HEX SOCKET CAP SCREW
M4x10 2
725416 RETAINER SCREW - M3x6 2
725416 RETAINER FOR MODULE 3mm 2
725427 BRACKET FOR FEEDTRACK 2
725428 FEED TRACK HEX SOCKET SCREW
1/4”-20 x 7.4mm 5
725426 FEED TRACK 1
725432 TUBE FOR END PLATE 1
DEPTH ADJUSTMENT PARTS QTY
725472 DEPTH CONTROL RETAINER 1
725474 DEPTH CONTROL SPRING 1
725473 DEPTH CONTROL ADJUSTMENT
WHEEL 1
725475 SNAP E RING E2 1
EXTENSION PARTS QTY
725476 EXTENSION 19” 1
729430 BIT EXTENSION 1
729431 HANDLE ASSEMBLY 1
725413
725470
725471
725414 (GREEN DOT)
725415 (GREEN)
725475
725473725472
725416 725474 725424
725422
725425
725432
725428
725427
725423
725476
725430
725431
725426
725416

Summary

HITACHI SuperDrive Auto-feed Screw System WARRANTY

Operating Instructions

Driver Bit Check and Forward-Reverse Switch

Ensure the driver bit is in good condition and the forward-reverse switch is in the forward position.

Screw Insertion and Feed Track Setup

Insert screws into the feed track and align the first screw with the nose piece for driving.

Nosepiece Adjustment for Screw Depth

Adjust the nosepiece to achieve a 1/8" to 1/4" gap between the nose piece and the screw tip.

Motor Activation and Locking

Turn on the motor before driving screws; the motor can be locked to the ON position.

Troubleshooting

Screws Not Driving or Seating Uniformly

Addresses issues like broken bits, incorrect depth settings, or worn parts causing driving problems.

Skipped Screws and Strip Feed Issues

Covers problems with indexing gears, worn modules, or binding strips leading to skipped screws.

Rapid Bit Wear

Explains that setting the depth control too deep can require excessive torque, causing rapid bit wear.

Other Points of Attention

Nosepiece Screw and End Plate Issues

Addresses lost nosepiece screws or damaged end plates that may require replacement parts.

Maintenance and Component Replacement

Routine Maintenance Checks

Daily inspection of nosepiece/trigger, lubrication of the index module roller, and wiping the tool.

Changing the Index Module or Bit

Instructions for replacing the index module and driver bit for optimal tool performance.

Safety Warnings

General Workplace and Tool Safety

Covers maintaining a clean work area, avoiding hazardous environments, and keeping bystanders away.

Personal Safety and Tool Operation

Includes wearing protective gear, proper tool handling, staying alert, and avoiding accidental starts.

Tool Maintenance and Repair Safety

Emphasizes proper cord care, using correct accessories, and ensuring qualified personnel perform repairs.

Hitachi Super drive series Specifications

General

Brand	Hitachi
Model	Super drive series
Category	Accessories
Language	English