What causes Hitachi YUTAKI S80 RWH-6.0VNFE Air Conditioner hydraulic alarm pressure?
If your Hitachi Air Conditioner displays 'Hydraulic alarm pressure', check the system for any leaks or blockages affecting water pressure. This alarm indicates that water pressure is not detected in the hydraulic cycle.
What to do if Hitachi YUTAKI S80 RWH-6.0VNFE shows Failure of discharge gas pressure sensor?
If your Hitachi Air Conditioner displays a 'Failure of discharge gas pressure sensor', check the connectors for any looseness or breakage. The issue may be a loose, disconnected, broken, or short-circuited connector.
How to fix Incorrect PCB Setting in Hitachi YUTAKI S80 RWH-6.0VNFE Air Conditioner?
If your Hitachi Air Conditioner shows 'Incorrect PCB Setting', correct the DSW settings. This issue is caused by a wrong DSW setting in the case of Co041.
What causes Water inlet thermistor abnormally (THMwi) in Hitachi Air Conditioner?
If your Hitachi Air Conditioner displays any of the following errors: Water inlet thermistor abnormally (THMwi), Water outlet thermistor abnormally (THMwo), Indoor Liquid Pipe Temp Thermistor Abnormality (THMl), Indoor Gas Pipe Temperature Thermistor Abnormality (THMg), Water Circuit 2 thermistor abnormally (THMwo2), Water DHW thermistor abnormally (THMdhwt), Auxiliary sensor 2 thermistor abnormally (THMaux2), Auxiliary sensor 1 thermistor abnormally (THMaux1), Water Plate HEX pipe thermistor abnormally (THMwohp), Suction R134a pipe thermistor abnormally (THMs), Discharge R134a pipe thermistor abnormally (THMd), check the connectors for any looseness or breakage. The cause may be a loose, disconnected, broken or short-circuited connector.
What causes Failure of suction gas pressure sensor in Hitachi YUTAKI S80 RWH-6.0VNFE Air Conditioner?
If your Hitachi Air Conditioner displays a 'Failure of suction gas pressure sensor', check the connectors for any looseness or breakage. The problem may stem from a loose, disconnected, broken, or short-circuited connector.
What to do if Hitachi YUTAKI S80 RWH-6.0VNFE Air Conditioner shows Transistor module protection activation?
Inspect the transistor module conditions.
How to solve Incorrect indoor unit setting on Hitachi Air Conditioner?
Correct the indoor unit capacity settings.
How to troubleshoot Hitachi Air Conditioner hydraulic alarm flow and water pump malfunction?
If your Hitachi Air Conditioner displays a hydraulic alarm related to flow and water pump malfunction, check the water pump for proper operation and repair or replace it if defective. This alarm indicates that water flow is not detected in the hydraulic cycle or the pump is defective.
What causes Hitachi YUTAKI S80 RWH-6.0VNFE to activate safety device from excessively low suction pressure?
If your Hitachi Air Conditioner activates the safety device from excessively low suction pressure, inspect refrigerant levels and piping for blockages. This issue is often due to a shortage or leakage of refrigerant, piping clogging, a closed expansion valve, or a locked fan motor.
Why does my Hitachi Air Conditioner activate safety device from excessively high discharge pressure?
If your Hitachi Air Conditioner activates the safety device due to excessively high discharge pressure, inspect the heat exchanger and refrigerant conditions. This activation can be caused by overload (obstruction of HEX, short circuit), a mixture of inert gas, or excessive refrigerant.
General| Brand | Hitachi |
|---|---|
| Model | YUTAKI S80 RWH-6.0VNFE |
| Category | Air Conditioner |
| Language | English |
Provides crucial safety precautions and warnings for handling and operating the heat pump system.
Specifies wiring size requirements for outdoor and indoor units based on current and cable types.
Details the location of DIP and rotary switches on the outdoor unit's PCB for configuration.
Illustrates main power supply and indoor/outdoor communication wiring connections.
Details input and output terminal connections for PC-ARFHE, 4-20mA, sensors, and valves.
Guides the user through initial system configuration based on installation type and components.
Details the procedure for purging air from the system, including duration and start command.
Guides through the unit test run process, specifying duration, mode, and start command.
Lists alarm codes displayed on the remote control switch and their detailed abnormalities.
To Next Page