HME WH200 User Manual

HM ELECTRONICS, INC. 14110 Stowe Drive, Poway, CA 92064 USA • Phone: 1-800-848-4468 Fax: (858) 552-0172
HME# 400G578
Rev A 3/31/08
Power
button
Figure 1. Headset power button
Figure 2. Headset buttons
and lights
Power
light
Transmit
light
WH200
Wireless Headset
OPERATING INSTRUCTIONS
SETUP
Power On/Off
Turn power on
Press and release the power button on the inside of
the headset housing, shown in Figure 1. A voice
message in the earpiece will say “Headset #” and the
power light on the opposite side of the earpiece will go
on. See Figure 2.
Turn power off
Press and hold the power button for approximately 3 seconds. A voice message in the earpiece
will say “Headset off,” and the power light on the opposite side of the earpiece will go off.
Configure Headset
Start with power OFF and press any of the following button combinations
while turning the power ON. After pressing the power button, immediately
release both buttons. Each of these settings has an associated voice
prompt. Listen to the voice prompt to confirm the setting.
Hands Free (HF) on/off mode
Press and hold ISO and the UP arrow ▲ while you press the power
button to turn the headset on in the HF mode. The headset will
remain in the HF mode, even if it is turned off and on again, until
you turn off the HF mode. To turn off the HF mode, with the power
off, press and hold ISO and the DOWN arrow ▼ while you press
the power button to turn the headset on.
ISO Lockout mode
To set the Headset with the ISO feature locked out, press and hold the IC1 button while you
press and release the power button to turn the headset on. You will hear “Power on, Headset #,
Version #, ISO off” in your Headset earpiece. When set up for the ISO Lockout mode, the ISO
button will operate the same as the IC1 button, in either hands-free or PTT communication. To
reset the ISO feature for normal ISO button communication, with the power off, press and hold
the ISO and IC1 buttons while you press and release the power button. You will hear “Power
on, Headset #, Version #, ISO on” in your Headset earpiece.
Lights-off operation
To prevent the power and transmit lights from coming on during headset operation, press and
hold the IC2 button while you press the power button to turn the headset on. To return the
lights to their normal functions, turn the power off and on again without pressing the IC2 button.

HME WH200 Specifications

General

Brand	HME
Model	WH200
Category	Headsets
Language	English

Summary

Setup Procedures

Power On/Off

Instructions for turning the headset on and off, including visual and audible indicators.

Configure Headset Settings

Options for Hands Free mode, ISO Lockout, and disabling indicator lights.

Headset Registration

Register Each WH200 Headset

Step-by-step guide for pairing a headset with the base station.

Successful Registration Indicators

Confirmation signals for successful headset registration.

Headset Operation

Wearing the Headset

Instructions for attaching the headset band and adjusting fit.

Putting on the Headset

Guidance on how to properly wear the headset and position the microphone.

Routine Operation Modes

Push-To-Talk (PTT) Mode

How to use the headset for two-way communication via PTT.

Hands-Free (HF) Mode

How to use the headset for continuous communication without pressing buttons.

Microphone Gain Adjustment

Adjusting the microphone sensitivity for optimal voice input.

Battery Management

Changing Batteries

Procedure for removing and replacing a weak headset battery.

Recharging Batteries

Instructions for charging headset batteries using the provided charger.

Compliance and Disposal Information

FCC Compliance and RF Exposure

Regulatory information regarding FCC rules and radio frequency exposure.

Waste Electrical and Electronic Equipment (WEEE)

Guidelines for the proper disposal of electronic equipment in the EU.