What to do if Hobart Welding Products Champion 10,000 Welding System engine stopped during normal operation?
If the engine stopped during normal operation: * Check the fuel level. * Check the oil level. * Check fuse F6, and replace it if it's open. * Check the low oil pressure shutdown switch. * Periodically recharge the battery (approximately every 3 months). * Replace the battery, if necessary.
Why does my Hobart Welding Products Champion 10,000 Welding System engine will not start?
If the engine won't start, you should: * Check the fuel level. * Check the battery voltage. * Check the battery connections and tighten if necessary. * Check the oil level. * Check the low oil pressure shutdown switch.
What to do if there is no output at generator power ac receptacles of Hobart Welding Products Welding System?
If there's no output at the generator power AC receptacles, try the following: * Reset the circuit breakers. * Press the optional GFCI receptacle Reset button. * Reset circuit breaker CB4. * Check plug PLG6 connection. Also, if the unit is overloaded, stop it and reduce the load. Then, restart the unit to reset the generator protection circuit and resume operation. If the problem persists, it may be necessary to have a Factory Authorized Service Agent check the brushes, slip rings, integrated rectifier SR2, and field control board PC1.
General| Fuel Type | Gasoline |
|---|---|
| Type | Engine-Driven Welding Generator |
| Max Output | 10000 W |
| Output Current Range | 40-225 Amps |
| Maximum Open Circuit Voltage | 80 VDC |
| Auxiliary Power | 120/240 VAC |
Explains symbols used in the manual for hazard identification.
Details hazards associated with arc welding processes and safety measures.
Covers potential dangers related to the engine, including fuel and moving parts.
Outlines risks associated with compressed air usage and handling.
Provides warnings about chemicals known to cause cancer or birth defects.
Lists key safety standards and organizations referenced in the manual.
Discusses electromagnetic fields and their potential effects, with minimization procedures.
Defines common symbols used in the manual and on the equipment.
Details the welding, power output, and engine specifications of the unit.
Provides physical measurements, weight, and safe operating angle limits for the unit.
Illustrates the generator's power output in amperes available at the receptacles.
Shows fuel consumption rates for different operating modes and loads.
Explains duty cycle percentages and their impact on operation and warranty.
Displays the generator's minimum and maximum voltage/amperage output capabilities.
Guides on safely moving, locating, and mounting the welding generator unit.
Outlines daily checks for the Robin-powered engine, including fuel and oil levels.
Outlines daily checks for the Kohler-powered engine, including fuel and oil levels.
Provides instructions for activating a dry charge battery before installation.
Details the procedure for safely connecting the unit's battery.
Instructions for correctly installing the exhaust pipe, ensuring safety.
Identifies and explains the connection points for weld output terminals.
Guides on properly connecting weld cables to the output terminals for safe operation.
Provides a chart for selecting appropriate weld cable sizes based on amperage and length.
Describes the functions of the various controls located on the front panel of the unit.
Offers advice and procedures for operating the engine in cold weather conditions.
A table to help select the correct amperage for specific stick welding electrodes.
Details the standard AC receptacles available on the unit and their power ratings.
Describes optional GFCI receptacles and their safety features and testing.
Provides wiring instructions for connecting a 240V plug, including load distribution.
A schedule for routine maintenance tasks for Robin-powered units.
Explains the information provided on the maintenance label for Robin engines.
Step-by-step guide for cleaning and maintaining the air cleaner element for Robin engines.
Explains the overload protection mechanisms and how to reset them.
Instructions for cleaning and inspecting the spark arrestor.
Detailed procedure for changing engine oil, oil filter, and fuel filter for Robin engines.
Guides on adjusting idle and weld/power speeds for Robin engines using a tachometer.
A schedule for routine maintenance tasks for Kohler-powered units.
Explains the information provided on the maintenance label for Kohler engines.
Step-by-step guide for cleaning and maintaining the air cleaner element for Kohler engines.
Explains the overload protection mechanisms and how to reset them.
Instructions for cleaning and inspecting the spark arrestor.
Detailed procedure for changing engine oil, oil filter, and fuel filter for Kohler engines.
Guides on adjusting idle and weld/power speeds for Kohler engines using a tachometer.
Provides guidance for diagnosing and resolving common welding and generator power issues.
Advice on selecting appropriate equipment and accessories for generator use.
Instructions for safely grounding the generator to a vehicle frame.
Guidelines for grounding the generator when supplying power to building electrical systems.
Explains how to calculate power requirements for various equipment and loads.
Provides power requirements for different types and sizes of industrial motors.
Lists approximate power requirements for common farm and home equipment.
Details power requirements for various contractor tools and equipment.
Explains how to determine the starting power needed for single-phase induction motors.
Discusses generator output limits and best practices for connecting loads.
Outlines typical connections for using the generator to supply standby power.
Guides on selecting extension cords based on load, length, and wire gauge for voltage drop.
A step-by-step guide for performing stick welding (SMAW) procedures.
A chart to help select electrodes and corresponding amperage for stick welding.
Describes the scratch start technique for initiating a welding arc.
Details the tapping technique for initiating a welding arc.
Illustrates correct electrode holder angles for groove and fillet welds.
Identifies common issues and characteristics of poor weld beads.
Describes the characteristics of a good weld bead and how to achieve it.
Explains how electrode angle, arc length, and travel speed impact weld bead shape.
Discusses stringer bead and weave bead techniques for electrode movement.
Details different types of butt joints and their preparation for welding.
Explains single-layer and multi-layer fillet welds for lap joints.
Describes fillet welds and multi-layer deposits for tee joints.
Outlines a test procedure for weld joints to check their integrity.
Identifies causes and corrective actions for porosity in weld metal.
Addresses causes and solutions for excessive spatter during welding.
Explains causes and corrective actions for incomplete fusion in weld metal.
Details causes and solutions for lack of penetration in welds.
Covers causes and corrective actions for excessive penetration in welds.
Discusses causes and corrective actions for burn-through during welding.
Addresses causes and solutions for waviness in weld beads.
Explains causes and corrective actions for distortion during welding.
An exploded view and parts list for the main assembly, showing Robin engine components.
Illustrates the front panel components and their part numbers.
Shows an exploded view of the generator assembly and its components.
To Next Page
