Hobbico Hobbistar 60 MK III User Manual

WARRANTY
Hobbico guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any
component parts damaged by use or modification. In no case shall Hobbico's liability exceed the original cost of the purchased kit. Further, Great
Planes reserves the right to change or modify this warranty without notice.
In that Hobbico has no control over the final assembly or material used for final assembly, no liability shall be assumed nor accepted for any damage
resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled product, the user accepts all resulting liability.
If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit immediately in new
and unused condition to the place of purchase.
ASSEMBLY INSTRUCTIONS
TM
© Copyright 2003 HCAZ3064 for HCAA2125 V1.1
Specifications:
Wingspan: 71 in [1805mm]
Wing Area: 888 sq in [57 dm
2
]
Weight: 7 - 8 lb [3180 - 3630g]
Wing Loading: 18 - 21 oz/sq ft [55 - 64 g/dm
2
]
Length: 55 in [1400mm]
Radio: 4-channel with 4 servos
Engine: .60 to .65 cu in [10.0 – 10.6cc] two-stroke
READ THROUGH THIS MANUAL BEFORE
STARTING CONSTRUCTION. IT CONTAINS
IMPORTANT INSTRUCTIONS AND WARNINGS
CONCERNING THE ASSEMBLY AND USE OF
THIS MODEL.
1610 Interstate Drive
Champaign, IL 61822
(217) 398-8970, Ext. 2
airsupport@hobbico.com
See more of our products at www.hobbico.com

Hobbico Hobbistar 60 MK III Specifications

General

Radio	4-channel
Construction	Balsa and plywood
Skill Level	Beginner
Type	RC Trainer Airplane
Engine	.40-.46 cu in (6.5-7.5 cc)
Servos	4
Weight	5.5 - 6.5 lbs (2.5 - 3 kg)

Summary

Warranty Information

Introduction

Safety Precautions

Important Safety Precautions

Crucial safety guidelines to ensure safe operation and prevent injury or damage.

Items Required

Radio System

Details on the necessary 4-channel radio control system and servos.

Engine Requirements

Specifications for the required .60 to .65 cu in two-stroke model airplane engine.

Tools, Building Supplies, and Accessories

List of essential tools and materials needed for assembly.

Optional Supplies and Tools

Recommended additional items to aid in model assembly and maintenance.

Field Equipment

Essential gear needed for flying the model at the field.

Kit Inspection

Ordering Replacement Parts

Tighten the Covering

Preparations

Assemble the Wing

Join the Ailerons

Instructions for attaching the ailerons to the wing panels using hinges and glue.

Join the Wing Halves

Procedure for joining the two wing halves securely using the provided wing joiner.

Assemble the Fuselage

Mount the Stabilizer and Fin

Steps for attaching the horizontal stabilizer and vertical fin to the fuselage for structural integrity.

Mount the Landing Gear

Mount the Engine

Install the Fuel Tank

Mount the Aileron Servo

Hook Up the Controls

Mount the Muffler, Prop and Fuel Lines

Prepare the Model for Flying

Balance the Model (C.G.)

Critical procedure to ensure proper flight stability by setting the center of gravity.

Center the Servos

Check the Control Directions

Center the Control Surfaces

Adjust the Throttle

Set the Control Throws

Identify Your Model

Balance Propellers

Checklist

Charge the Batteries

Gather Your Tools

Flight Preparation

Check the Controls

Verifying all flight controls respond correctly on the field before flight.

Range Check the Radio

Ground Check

Engine Safety Precautions

AMA Safety Code

Flying Instructions

Taxiing Procedure

Takeoff Procedure

Flight Operations

Landing Procedure

Maintenance Tips