Honda UNICORN CBF160A 2020

Questions and Answers

A
aaron00Aug 4, 2025
What to do if Honda UNICORN CBF160A 2020 starter motor operates but engine does not start?
- B
  bauernatalieAug 4, 2025
  If the starter motor operates but the engine doesn't start, begin by verifying the engine starting procedure is correct. Next, ensure there's fuel in the tank and that the engine stop switch is properly positioned. Check the PGM-FI malfunction indicator lamp (MIL). If the lamp is lit, contact your dealer promptly. Also, inspect the battery connections for looseness or corrosion. If the issue persists, take your motorcycle to the dealer for inspection.
M
Miguel HoustonAug 8, 2025
How to charge a dead battery on a Honda UNICORN CBF160A 2020 Motorcycle?
- G
  George MirandaAug 8, 2025
  To charge a dead motorcycle battery: * Use a motorcycle battery charger. * Remove the battery from the motorcycle before charging. * Avoid using an automobile-type battery charger, as it can cause damage. If the battery doesn't recover after charging, contact your dealer.
M
Mary MillsAug 14, 2025
What to do if Honda UNICORN CBF160A 2020 fuse is blown?
- W
  William BradleyAug 14, 2025
  If a fuse blows, follow these steps: 1. Consult “Inspecting and Replacing Fuses”. 2. Remove the left side cover. 3. Open the fuse box cover. 4. Use the fuse puller from the tool kit to check each fuse. 5. Replace the blown fuse with a spare of the same rating. If fuses repeatedly blow, have your motorcycle inspected by your dealer, as this indicates an electrical problem.
L
Lisa RobertsAug 18, 2025
What to do if PGM-FI malfunction indicator lamp (MIL) is on in Honda Motorcycle?
- M
  Melissa Pratt DDSAug 18, 2025
  If the PGM-FI indicator comes on while riding, it indicates a potential issue with the PGM-FI system. Reduce speed and have your vehicle inspected by your dealer as soon as possible. Also, if the indicator does not come on when the ignition switch is in the ON position, check your vehicle. If the indicator does not go off at speeds above 5 km/h (3 mph), have your vehicle inspected.
S
Shane SantiagoAug 25, 2025
How fast can I drive after an emergency tire repair on my Honda UNICORN CBF160A 2020?
- K
  Kevin JohnsonAug 25, 2025
  If you've made a temporary tire repair, ride slowly and carefully, and do not exceed 50 km/h (30 mph) until the tire is replaced.
S
Shannon StewartAug 28, 2025
What happens if a torque wrench wasn't used during the assembly of my Honda UNICORN CBF160A 2020 brakes?
- R
  Ronald ThompsonAug 28, 2025
  If a torque wrench was not used for installation, see your dealer as soon as possible to verify proper assembly.

Summary

Welcome

A Few Words About Safety

Safety Guidelines

Essential Riding Practices

Advice on safe riding, protective gear, and defensive driving.

Learning and Practice

Practice riding in a safe area to familiarize with vehicle handling.

Image Labels Explained

Safety Label Meanings (DANGER, WARNING, CAUTION)

Explains the meaning of DANGER, WARNING, and CAUTION safety labels.

Safety Precautions and Protective Apparel

General Safety Precautions

General advice on riding cautiously and considering passenger/other riders' safety.

Helmet Requirements

Use safety-standard certified, high-visibility helmet that fits securely.

Gloves Requirements

Use full-finger leather gloves with high abrasion resistance.

Boots or Riding Shoes Requirements

Wear sturdy boots with non-slip soles and ankle protection.

Jacket and Trousers Requirements

Wear protective, highly visible, long-sleeved jacket and durable trousers.

Riding Precautions

Running-in Period Guidelines

Guidelines for the first 500 km: avoid full throttle, hard braking, ride conservatively.

Brake Usage and Safety

Avoid hard braking, use both brakes, be cautious on low traction surfaces.

Anti-lock Brake System (ABS) Functionality

Explains ABS function, limitations, and non-operation for rear wheel.

Engine Braking and Wet Conditions Advice

Advice on engine braking, wet weather riding, and parking.

Parking Procedures

Park on firm level surface, secure handlebar, use side/centre stand.

Refuelling and Fuel Guidelines

Fuel Cap Operation and Safety Warnings

Steps for opening/closing fuel cap and safety warnings about petrol.

Accessories & Modifications

Warnings on Modifications and Accessories

Warnings about improper accessories, modifications, trailers, and sidecars.

Loading Guidelines

Overloading and Improper Loading Warnings

Warnings about the dangers of overloading and improper cargo placement.

Parts Location Overview

Identifying Key Vehicle Parts

Diagram showing location of various parts and references to their pages.

Seat Removal Reference

Reference to page for seat removal procedure.

Instruments and Gauges

Speedometer, Tripmeter, Odometer, and Fuel Gauge

Explains the function of speedometer, tripmeter, odometer, and fuel gauge.

Tachometer and Red Zone Warning

Displays engine speed (RPM) and warns against operating in the red zone.

Indicator Lights Explained

PGM-FI and ABS Indicator Functions

Explains the PGM-FI and ABS malfunction indicator lights.

Neutral and Turn Signal Indicators

Explains the neutral and turn signal indicator lights.

High Beam Indicator

Indicates when the high beam is activated.

Vehicle Switches and Controls

Handlebar Controls (Horn, Signals, Lights)

Describes horn, turn signal, and headlight dimmer/passing switches.

Engine Stop and Start Buttons

Explains the function of the engine stop and start buttons.

Ignition Switch and Steering Lock

Ignition Switch Operation and Positions

Explains the ON, OFF, and LOCK positions of the ignition switch.

Steering Lock Procedure

Steps for locking and unlocking the steering to prevent theft.

Starting the Engine

Engine Starting Procedures and Notices

Procedures for starting the engine, including important notices.

Altitude Considerations for Engine Performance

Advice on engine performance at high altitudes.

Shifting Gears

Five-Speed Transmission Pattern

Describes the 5-speed forward shift pattern (one-down, four-up).

Refuelling and Fuel Guidelines

Fuel Cap Operation and Safety Warnings

Steps for opening/closing fuel cap and safety warnings about petrol.

Storage Equipment Locations

Tool Kit, Document Bag, and First Aid Kit

Location of tool kit, document bag, and first aid kit under the seat.

Helmet Holder Usage

Helmet Holder Safety Warning

Warning against using the helmet holder while riding.

Importance of Vehicle Maintenance

Essential Maintenance Practices and Warnings

Explains maintenance importance, safety, and warnings about improper practices.

Maintenance Schedule Overview

Schedule Details and Professional Service

Outlines maintenance requirements, professional service, and owner costs.

Maintenance Fundamentals: Pre-ride Inspection

Pre-ride Inspection Importance

Importance of pre-ride checks for safety and convenience.

Pre-ride Inspection Checks

List of items to check before riding: fuel, throttle, oil, chain, brakes, lights, etc.

Replacing Parts Safely

Emphasis on using genuine Honda parts and warnings against non-genuine parts.

Maintenance Fundamentals: Battery Care

Battery Maintenance and Notices

Care for maintenance-free battery, terminal cleaning, and handling notices.

Maintenance Fundamentals: Battery Safety

Emergency Electrolyte Handling and Gas Hazard

First aid for electrolyte splashes and warnings about battery gas hazards.

Cleaning Battery Terminals

Steps to clean corroded battery terminals.

Maintenance Fundamentals: Fuses

Fuse Inspection, Replacement, and Warnings

Procedures for checking, replacing fuses, and warnings about rating and accessories.

Maintenance Fundamentals: Engine Oil

Engine Oil Checks and Selection Criteria

Checking oil level and guidelines for selecting appropriate engine oil.

Maintenance Fundamentals: Brakes and Drive Chain

Brake Fluid Handling and Drive Chain Care

Proper handling of brake fluid and regular inspection/lubrication of the drive chain.

Maintenance Fundamentals: Tyre Inspection

Tyre Inspection (Damage, Wear, Pressure)

Procedures for checking tyre air pressure, damage, and abnormal wear.

Maintenance Fundamentals: Tyre Tread Depth

Inspecting Tyre Tread Depth

Checking tread wear indicators and replacing tyres when minimum depth is reached.

Tyre Condition Warning

Riding on worn/improperly inflated tyres causes crashes and injury.

Maintenance Fundamentals: Air Cleaner

Air Cleaner Maintenance and Warnings

Information on the viscous air cleaner element and service recommendations.

Tool Kit Contents

Included Tools and Their Use

Lists tools in the kit and their utility for roadside repairs.

Removing & Installing Battery

Battery Removal and Installation Steps

Detailed procedures for removing and installing the vehicle battery.

Removing & Installing Drive Chain Case

Drive Chain Case Removal and Installation

Steps for removing and installing the drive chain case.

Removing & Installing Headlight Case

Headlight Case Removal and Installation

Steps for removing and installing the headlight case.

Removing & Installing Seat

Seat Removal and Installation Procedures

Procedures for removing and installing the vehicle seat.

Removing & Installing Side Cover

Side Cover Removal and Installation

Steps for removing and installing the vehicle's side covers.

Spark Plug Checks

Spark Plug Inspection and Specification

Procedure for inspecting spark plug condition and reference to specifications.

Spark Plug Heat Range Warning

Warning about using spark plugs with incorrect heat ranges.

Spark Plug Gap Adjustment and Tightening

Checking and Adjusting Spark Plug Gap

How to check and adjust the spark plug gap.

Spark Plug Tightening Procedure and Warning

Instructions for tightening the spark plug and warnings about improper tightening.

Engine Oil Level Check

Procedure for Checking Engine Oil

Step-by-step guide to checking the engine oil level.

Engine Oil Addition and Changing

Adding Engine Oil and Overfilling Warning

Procedure for adding oil and warnings about overfilling.

Engine Oil Change Recommendation

Recommendation to have oil changes performed by a dealer.

Engine Oil Draining and Refilling

Draining, Refilling, and Checking Engine Oil

Steps for draining old oil, refilling with new oil, and final checks.

Front Brake Fluid Check

Procedure for Checking Front Brake Fluid Level

Steps to check front brake fluid level and reservoir condition.

Front Brake Pad Inspection

Inspecting Front Brake Pad Wear

Procedure to check front brake pad wear using the indicator.

Front Brake Pad Replacement Advice

Recommendation to replace both front brake pads simultaneously by a dealer.

Rear Brake Pedal Freeplay Check and Adjustment

Inspecting Rear Brake Pedal Freeplay

Procedure to measure and inspect rear brake pedal freeplay.

Adjusting Rear Brake Pedal Freeplay

Procedure to adjust the rear brake pedal freeplay using the adjusting nut.

Rear Brake Shoe Wear Inspection

Inspecting Rear Brake Shoe Wear Indicator

Procedure to inspect rear brake shoe wear using the indicator.

Adjusting Brakelight Switch

Procedure for Adjusting Brakelight Switch

Steps to adjust the brakelight switch for proper operation.

Side Stand Check

Checking Side Stand Operation and Spring

Procedure to check the side stand operation and spring condition.

Drive Chain Inspection

Checking Drive Chain Slack and Specification

Procedure to check drive chain slack and its specified measurement.

Drive Chain Wear Check

Procedure to check drive chain wear using the wear label.

Adjusting Drive Chain Slack

Drive Chain Slack Adjustment Procedure

Steps for adjusting drive chain slack using adjusting nuts and checking alignment.

Clutch Lever Freeplay Check

Checking Clutch Lever Freeplay and Cable

Procedure to check clutch lever freeplay and clutch cable condition.

Clutch Freeplay Specification and Warning

Specifies correct freeplay and warns about improper adjustment.

Adjusting Clutch Lever Freeplay

Clutch Lever Freeplay Adjustment Steps

Steps to adjust clutch lever freeplay and test its operation.

Throttle Operation Check

Checking Throttle Operation and Freeplay

Checking throttle rotation, smoothness, and freeplay.

Throttle Freeplay Specification

Specifies the correct throttle grip freeplay measurement.

Crankcase Breather Cleaning

Procedure for Cleaning Crankcase Breather

Steps to remove the right side cover and clean the crankcase breather.

Adjusting Headlight Aim

Procedure for Adjusting Headlight Vertical Aim

Steps to adjust the vertical aim of the headlight using an adjusting bolt.

Adjusting Rear Suspension

Spring Preload Adjustment Procedure

How to adjust rear suspension spring preload using the adjuster and pin spanner.

Spring Preload Adjustment Warnings

Warnings about direct adjustment and exceeding adjuster limits.

Engine Will Not Start: Starter Motor Issues

Troubleshooting Starter Motor Problems

Checks for starter motor operation issues when the engine won't start.

Warning Indicators On or Flashing

PGM-FI and ABS Indicator Malfunctions

Explains what to do if PGM-FI or ABS indicators show malfunctions.

Tyre Puncture and Wheel Removal

Emergency Tyre Repair and Wheel Removal

Procedures for emergency tyre repair and removing wheels.

Temporary Tyre Repair Safety Warning

Warnings about the risks of riding with temporary tyre repairs.

Front Wheel Removal and Installation

Front Wheel Removal Steps and Warnings

Detailed steps for front wheel removal and associated warnings.

Front Wheel Installation and Checks

Front Wheel Installation Steps and Notices

Detailed steps for front wheel installation and notices.

Post-Installation Wheel Checks

Checks for wheel rotation and brake drag after installation.

Rear Wheel Removal

Steps for Rear Wheel Removal

Step-by-step procedure for removing the rear wheel.

Rear Wheel Installation and Adjustments

Rear Wheel Installation Steps

Step-by-step procedure for installing the rear wheel.

Rear Wheel Installation Adjustments and Checks

Adjusting drive chain, brake freeplay, and final checks after installation.

Electrical Trouble: Battery and Bulbs

Battery Charging and Jump Starting Warning

Procedure for charging a dead battery and warning against jump starting.

Burned-out Light Bulb Replacement

Procedure for replacing a burned-out light bulb.

Headlight Bulb Replacement

Headlight Bulb Removal and Installation

Steps for removing and installing the headlight bulb.

Handling New Headlight Bulb

Precautions for handling the new headlight bulb.

Other Bulb Replacements

Brakelight;Taillight Bulb Replacement

Procedure for replacing brakelight/taillight bulbs.

Turn Signal Bulb Replacement

Procedure for replacing front/rear turn signal bulbs.

Blown Fuse Check and Replacement

Fuse Box Fuse Inspection and Replacement

Procedure for checking and replacing blown fuses in the fuse box.

Repeated Fuse Failure Warning

Warning that repeated fuse failure indicates an electrical problem.

Main Fuse Check and Replacement

Main Fuse Inspection and Replacement Procedure

Procedure for checking and replacing the main fuse.

Repeated Main Fuse Failure Warning

Warning that repeated main fuse failure indicates an electrical problem.

Unstable Engine Operation

Potential Causes and Riding Advice

Discusses fuel pump filter clogging and advice for unstable engine operation.

Keys and Ignition System

Ignition Key Information and Security

Importance of recording key number and storing spare key safely.

Instruments, Controls, and Features

Ignition Switch and Engine Stop Switch Operation

Explains ignition switch positions and engine stop switch usage.

Odometer, Tripmeter, Document Bag, and Cut-off System

Describes odometer, tripmeter, document bag location, and ignition cut-off system.

Caring for Your Vehicle: Washing

Washing Procedures and Precautions

Guidelines for washing the vehicle, including rinsing, cleaning, and drying.

Post-Wash Lubrication and Waxing

Lubricating moving parts and applying wax for corrosion prevention.

Washing Precautions

Water Usage Warnings During Washing

Warnings about water direction near air cleaner, muffler, headlight, and under seat.

Matte Surface Cleaning Guidelines

How to clean matte painted surfaces without damage.

Component Care: Aluminium, Panels, Exhaust

Care for Aluminium Components

Guidelines for cleaning aluminium parts to prevent corrosion and scratches.

Panel and Exhaust System Care

Procedures for cleaning panels and exhaust pipe/muffler.

Storing Your Vehicle

Extended Storage Procedures

Guidelines for washing, waxing, and preparing the vehicle for long-term storage.

Battery Care During Storage

How to prepare the battery for storage to prevent discharge.

Transporting Your Vehicle

Safe Transportation Methods and Warnings

Proper methods for transporting the vehicle and warnings about towing damage.

You & the Environment

Environmental Protection Responsibility

Importance of environmental protection, using sensible cleaners, and recycling.

Serial Numbers

Locating and Recording Serial Numbers

Information on frame and engine serial numbers for registration and parts.

Fuels Containing Alcohol

Acceptable Fuel Blends and Risks

Information on usable fuel blends and risks of high ethanol content.

Catalytic Converters

Converter Function, Protection, and Maintenance

Explains converter function, protection guidelines, and impact of engine health.

Specifications: Main Components

Vehicle Dimensions, Weight, and Displacement

Table listing key vehicle dimensions, weight, capacity, and engine displacement.

Specifications: Service Data

Tyre, Oil, Chain, and Spark Plug Details

Table detailing tyre specifications, engine oil, drive chain, and spark plug data.

Warranty Policy Overview

HMSI Warranty Terms and Conditions

Details the HMSI warranty for the vehicle, coverage period, and exclusions.

Proprietary Parts Warranty (Tyres;Battery)

How claims for tyres and battery are handled by their respective manufacturers.

Warranty Policy: Exclusions and Claim Conditions

Conditions for Making Warranty Claims

Requirements for customers to make valid warranty claims.

General Warranty Exclusions

Lists common exclusions like missed services, wear parts, and improper use.

Emission Warranty Details

Emission Warranty Terms and Applicability

Explains emission warranty terms, coverage, and applicability conditions.

Emission Warranty Claims and Replacements

Emission Warranty Claim Admission Criteria

Criteria for admitting emission warranty claims and required evidence.

Emission Component Replacement Policy

Manufacturer's policy on replacing emission control components.

Emission Warranty Compliance and Requirements

Emission Compliance Repair Costs and Documentation

Cost responsibility for emission compliance repairs and required documentation.

General Warranty Requirements

Key requirements for warranty validity: following manual, maintenance, and timely reporting.

Warranty Exclusions and Documentation

Specific Exclusions from Warranty

Details specific conditions like vehicle usage, parts modifications, and odometer tampering.

Required Documentation for Warranty Claims

Lists essential documents like PUC, manual, logbook, and receipts.

Emission Warranty Scope and Limitations

Emission Warranty vs. Product Warranty

Clarifies that emission warranty is additional to and parallel with product warranty.

Emission Warranty Coverage Limitations

Defines what the emission warranty covers and does not cover.