Honeywell 6162 - User Manual

6162 SERIES KEYPAD PROGRAMMING SUPPLEMENT
Introduction
The 6162 series of keypads (6162, 6162V, 6162RF) provide the following features when used with control panels
having the firmware revisions listed below:
• Menu Mode Programming for easy programming of options typically used in a basic installation. See menu
Mode Programming section for details.
• Menu-Based User Code Programming to easily manage system users. The master user can do the following:
- add new users and user codes
- delete users
- assign user attributes, including authority level, access group, partition, and RF user number
Refer to the user guide included with the keypad for details on using menu-based user code programming.
Menu Mode Programming with 6162 Series Keypads
Menu mode programming provides easy programming of the following options:
• Entry of accounts and phone numbers
• Enabling various reports
• Setting entry & exit delays
• Setting alarm & fire sounder timeouts
• Assigning the Installer code
• Enabling the Auto-Stay feature
• Programming zone attributes
Menu mode programming is supported by the following
controls having the listed or higher firmware revision levels:
Control Firmware Rev. Level
VISTA-10P 4.16
VISTA-15P 9.16
VISTA-20P 9.16
VISTA-21iP 3.16
Navigation Keys for Menu Mode Programmin
g
Ke
y
Function
Settings Key
Enter and exit
Menu mode
programming
.
Night Stay Advance to the next page.
[∗
∗∗
∗]
Advance to the next field. If at the
last field on a page, it advances to
the next page.
[#]
Goes to the previous field. If at the
first field, goes to the previous page.
SETTINGS KEY
(ENTER MENU MODE
PROGRAMMING)
CLEAR
ENTRY
TOGGLE
ENTRIES
NO
YES
AWAY
STAY
NEXT PAGE
NEXT FIELD
PREVIOUS FIELD
6162 Series_Keypad_1
To enter menu mode programming:
1. Enter panel programming mode (installer code + 800).
2. Press and hold the Settings key for 2 seconds
The word “communicating” appears briefly, then the first page of programming options appears.
Programming Menus
Menu mode programming consists of seven (7) pages of menus as follows:
Menu Menu Function
1 Phone Number & Account Number Programming
2 Reporting Options (alarm restore, trouble, bypass, AC loss, low battery, test, RF low battery)
3 System Reports (RF jam, cancel, event log full, exit error, open, close away, close stay)
4
Timing & Miscellaneous Options (exit/entry delays, alarm sounder timeout, fire alarm sound timeout, installer
code, auto-stay enable)
5 Zone Number (prompt to begin zone programming)
6
Zone Programming (zone type, report enable, partition, input type, serial number, response time, hardwire type,
zone descriptor)
7 Quit Menu Mode Programming

Summary

Introduction to 6162 Keypad Programming

Menu Mode Programming Overview

Explains options for easy programming of features used in a basic installation.

User Code Programming Features

Details on managing system users and codes, including attributes and access.

Menu Navigation and Controls

Core Programming Menus

Menu 1: Phone & Account Number Programming

Configure phone numbers and account numbers for reporting and downloads.

Menu 2: Enabling Reporting Options

Enable various reports for ADEMCO Contact ID reporting format.

Menu 3: Enabling System Reports

Configure system-specific reports like RF Jam, Cancel, and Event Log Full.

Menu 4: Timing and Miscellaneous Options

Set entry/exit delays, alarm timeouts, installer code, and auto-stay.

Menu 5: Enter Zone Number

Initiates zone programming by prompting for the desired zone number.

Menu 6: Zone Programming Details

Configure zone attributes: type, report enable, partition, input type, and descriptor.

Menu 7: Quit Menu Mode Programming

Provides options to exit programming mode with or without re-entry.

Zone Descriptor Library

Honeywell 6162 Specifications

General

Type	Keypad
Compatibility	Honeywell security systems
Weight	0.5 lbs
Power Source	Wired
Backlit Keys	Yes
Display	LCD
Power	DC
Voltage	12 V
Operating Temperature	0 to 49 °C
Keypad Type	Fixed